2.470 results (0,14452 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Global Fire Equipment GFE-MIO Mains Switching IO Module CW Isolator

Global Fire Equipment GFE-MIO Mains Switching IO Module CW Isolator

Global Fire Equipment GFE-MIO Mains Switching IO Module CW IsolatorThe MAINS IO Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the Fire Alarm Control panel using normally open dry contact connections.The connection to the input is monitored for fault open or short circuit and Alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing systems etc.Module is provided with a loop short-circuit isolator and with a voltage free single pole change over mains rated output. The output relay is always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an onboard red LED.An 8-way D.I.L. switch is provided to configure the modules address. This value can be set in the range 1 to 125.Key FeaturesFast Activation ResponseLoop PoweredFive Status LEDs providedLow Power ConsumptionModule features an integral short-circuit loop isolatorSingle mains rated relay contact

GBP 61.76
1

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP Relay Output Card as per CFP762 8 outputs per zone relays CFP763An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote and eight output per zone relays.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Output per zone relays will changeover when the corresponding zone is in alarm subject to certain conditions - for full details refer to the instructions downloadable below.Outputs are NOT designed to switch mains voltages.

GBP 67.02
1

Elmdene G13803N-A 12V Switch Mode Power Supply Unit 3A A-Box

Elmdene G13803N-A 12V Switch Mode Power Supply Unit 3A A-Box

Elmdene G13803N-A 12V Switch Mode Power Supply Unit 3A A-BoxThe 12V dc G Range N Series power supplies has been designed for CCTV access control and general purpose applications that require the use of a standby battery. The products use energy efficient switch mode technology and have a universal mains supply input 90264V ac. Elmdenes FOM4 or FOM8 units can be fitted to give 4 or 8 independent fused outputs if required. The modular range consists of 1A 2A 3A 4A and 5A power variants with full rated current to load and also feature a fully regulated output with low ripple and noise. Unboxed module only versions are also available if required.Advantages of Switch Mode TechnologyElmdene products using switch mode technology are typically 80-87 efficient. This can save your customers money by reducing their energy bills and carbon footprint. Switch mode technology provides for lower power consumption provides cool running and energy efficient products that can result in improved long term reliability.Key Features13.8V dc outputCost effective switch mode technologyHigh energy efficient - reducing energy billsModular construction means easy maintenance and upgradingFull rated current to load 0.5A battery charging90 to 264V ac rangeElectronic overload protectionMains transient protectionLED indicationMains statusFaultScreen printing available3 year warranty12V d.c. Switch Mode PSU 13.8V 3Amp to load 0.5A battery charging.Efficient Switch Mode operation.Multi LED status indication.Fit up to 7Ah battery.A Box 200h x 230w x 80d - Hinge lidPlease note The image is for illustrative purposes only. Please contact us for further information.

GBP 60.37
1

Fike 540-0030 CIE-A-200 CIE-A-400 Fire Panel Flush Mount Bezel 540-0030

Fike 540-0030 CIE-A-200 CIE-A-400 Fire Panel Flush Mount Bezel 540-0030

Fike 540-0030 CIE-A-200 CIE-A-400 Fire Panel Flush Mount Bezel 540-0030A specially designed recessing cradle enables seamless installation of the Fike CIE-A-200 1 Loop and CIE-A-400 2 Loop fire panels ensuring a flush appearance. The required cut-out dimensions for securely mounting the control panel are 354mm width x 334mm height. When expertly flush-mounted the panel aligns at a depth of 83mm within the cavity with a 36mm projection from the surface for optimal integration.Product featuresEnables the flush installation of Fike CIE-A-200 1-loop and CIE-A-400 2-loop addressable fire panels.

GBP 72.11
1

STI STI-1210A Sounder Strobe with Spacer A

STI STI-1210A Sounder Strobe with Spacer A

STI STI-1210A Sounder Strobe with Spacer AThis virtually indestructible cover slotted for sounderstrobe unit is specifically designed to prevent vandalism and accidental damage to a signal unit of a fire alarm system. Moulded in clear thick UV-stabilised polycarbonate material with slots allowing the sounder or fire voice speaker to be heard. There are a variety of spacers available to accommodate larger sounderstrobe units and retrofits - as well as weather resistance and surface mounted applications. Spacer B has a solid back and is moulded with an integral mounting box. For extreme conditions where dampness water or dust are frequently present we recommend using STIs unique new Enviro Kit.Both the cover and circular back box are moulded from clear thick polycarbonate material that is UV-stabilized against discolouration. It is backed by a three year guarantee against breakage in normal use.Key FeaturesProtective cover for hornstrobe units4 deep enclosed back boxEasy access for service3 year guarantee216 mm H x 165 mm W x 159 mm D - Please note Due to the curvature of this model the depth stated will vary

GBP 63.95
1

STI STI-SA5600-A Select-Alert SirenStrobe - Amber Rectangular

STI STI-SA5600-A Select-Alert SirenStrobe - Amber Rectangular

STI STI-SA5600-A Select-Alert SirenStrobe - Amber RectangularThe Select-Alert Siren and Strobes are a highly effective additional signalling device to alert to any unauthorised use and tampering of important devices when used in conjunction with a triggering device. The combination of alarm and super bright flashing LEDs offers excellent protection for an array of circumstances as they draw attention in a hurry.The sirens and strobes will work in conjunction with push buttons protective covers as well as many other products.Key FeaturesHelps stop unauthorised use of important devicesCombination of siren and super bright flashing LEDs8 flash patterns with speed selectionStrobe only or sounder only control105 or 85 dB alarm12-24 VDC122.7 mm H x 81.7 mm W x 53.3 mm D

GBP 83.78
1

STI STI-SA5500-A Select-Alert SirenStrobe - Amber Round

STI STI-SA5500-A Select-Alert SirenStrobe - Amber Round

STI STI-SA5500-A Select-Alert SirenStrobe - Amber RoundThe Select-Alert Siren and Strobes are a highly effective additional signalling device to alert to any unauthorised use and tampering of important devices when used in conjunction with a triggering device.The combination of alarm and super bright flashing LEDs offers excellent protection for an array of circumstances as they draw attention in a hurry. The sirens and strobes will work in conjunction with push buttons protective covers as well as many other products.Key FeaturesHelps stop unauthorised use of important devicesCombination of siren and super bright flashing LEDs32 selectable sounds8 flash patterns with speed selectionStrobe only or sounder only controlLow battery signal105 or 85 dB alarm12-24 VDCIP6698.2 mm H x 98.2 mm W x 94.6 mm D

GBP 87.32
1

STI STI-1221A Strobe Stopper with Spacer Type A

STI STI-1221A Strobe Stopper with Spacer Type A

STI STI-1221A Strobe Stopper with Spacer Type AThis virtually indestructible cover slotted for sounderstrobe unit is specifically designed to prevent vandalism and accidental damage to a signal unit of a fire alarm system. Moulded in clear thick UV-stabilised polycarbonate material with slots allowing the sounder or fire voice speaker to be heard. There are a variety of spacers available to accommodate larger sounderstrobe units and retrofits - as well as weather resistance and surface mounted applications. Spacer B has a solid back and is moulded with an integral mounting box. For extreme conditions where dampness water or dust are frequently present we recommend using STIs unique new Enviro Kit.Both the cover and circular back box are moulded from clear thick polycarbonate material that is UV-stabilized against discolouration. It is backed by a three year guarantee against breakage in normal use.Key FeaturesProtective cover for strobe units4 deep enclosed back boxEasy access for service3 year guarantee216 mm H x 165 mm W x 159 mm D - Please note Due to the curvature of this model the depth stated will vary

GBP 59.21
1

STI STI-34188 8-Zone Relay Board for Exclusive Use with 34108

STI STI-34188 8-Zone Relay Board for Exclusive Use with 34108

STI STI-34188 8-Zone Relay Board for Exclusive Use with 34108This 8-Zone Relay Board provides an individual dry Form C contact per zone. The relays follow the input to the receiver supplying an individual output per zone. The board has a low current draw and fits in most panel cabinets such as burglar alarm or data gathering types. There is a four conductor interconnect cable included between the receiver and the relay board. The relays are rated to switch 3A 125VAC 3A 28VDC resistive loads. The board is designed to be exclusively used with the STI 34108.Key Features8 Momentary Form C Relay contacts rated 3A 125 VAC 3A 28VDC2 ft. - 4 conductor interconnect cable to 8-Channel Receiver12 V InputAdhesive Pad Mounts quantity 4Confirmation LEDsMeasures- 6 x 2 x 12

GBP 74.30
1

Cooper TA16-SS-BEZ Type A Outstation Bezel - Stainless Steel - Flush Mount

Cooper TA16-SS-BEZ Type A Outstation Bezel - Stainless Steel - Flush Mount

Cooper TA16-SS-BEZ Type A Outstation Bezel - Stainless Steel - Flush MountThe TA16-SS-BEZ is a bezel designed for use with the VoCALL TA16 Type A Outstation.The VoCALL Type A Digital Outstation is a compact unit which offers easy access via a magnetic push catch door.The outstation is compatible with VoCALL digital systems for use as a standard fire telephone or disabled refuge call point. It is compatible with all VoCALL digital systems.Key FeaturesType A Outstation BezelStainless steelFlush mount

GBP 86.80
1

RGL Electronics 2401SM-2MP 27.6V DC Power Supply In A Large Housing

RGL Electronics 2401SM-2MP 27.6V DC Power Supply In A Large Housing

RGL Electronics 2401SM-2MP 27.6V DC Power Supply In A Large HousingManufactured by RGL the 2401SM-2MP is a 27.6V DC power supply in a large housing with a multi-indicator.It Includes Mains Battery PSU monitoring via voltage free outputs and is designed to house up to 2 x 9 Ah battery. Additional battery charging of 300mA - includes Deep Discharge Protection.Ideal for fire systems and 24 Volt systems that require a battery backup i.e. Access Control Entry Systems and General use.Key FeaturesBattery mains monitoringMild steel constructionWhite powder coated finishHinged style boxWiring productMore efficient and environmentally friendlyTop. bottom and rear cable entryFront tamperTechnical SpecificationsFull current to load1 Amp PSU27.6VDC regulated outputAdditional battery chargingDeep discharge protectionCurrent limitingShort circuit protectionMains transient protectionCompliant to EMC EN61000-6-1 3Can house 2 batteries up to 12V 9Ah

GBP 75.78
1

RGL Electronics 2402SM-2MP 27.6V DC Power Supply In A Large Housing

RGL Electronics 2402SM-2MP 27.6V DC Power Supply In A Large Housing

RGL Electronics 2402SM-2MP 27.6V DC Power Supply In A Large HousingManufactured by RGL the 2402SM-2MP is a 27.6V DC power supply in a large housing with a multi indicator.It Includes Mains Battery PSU monitoring via voltage free outputs and is designed to house up to 2 x 9 Ah battery. Additional battery charging of 300mA - includes Deep Discharge Protection.Ideal for fire systems and 24 Volt systems that require a battery backup i.e. Access Control Entry Systems and General use.Key FeaturesBattery mains monitoringMild steel constructionWhite powder coated finishHinged style boxWiring productMore efficient and environmentally friendlyTop. bottom and rear cable entryFront tamperTechnical SpecificationFull current to load2 Amp PSU27.6VDC regulated outputAdditional battery chargingDeep discharge protectionCurrent limitingShort circuit protectionMains transient protectionCompliant to EMC EN61000-6-1 3Can house 2 batteries up to 12V 9Ah

GBP 85.16
1

RGL Electronics 1202SM-2MP 13.8V DC Power Supply In A Large Housing

RGL Electronics 1202SM-2MP 13.8V DC Power Supply In A Large Housing

RGL Electronics 1202SM-2MP 13.8V DC Power Supply In A Large HousingThe 1202SM-2MP is a 13.8V DC power supply in a large housing with a multi-indicator.It includes the Mains Battery PSU monitoring via voltage free outputs and is designed to house up to 2 x 9 Ah battery.Additional battery charging of 300mA - includes Deep Discharge Protection.Key FeaturesBattery mains monitoringMild steel constructionWhite powder coated finishHinged style boxWiring productMore efficient and environmentally friendlyTop. bottom and rear cable entryFront tamperTechnical SpecificationsFull current to load2 Amp PSU13.8VDC regulated outputAdditional battery chargingDeep discharge protectionCurrent limitingShort circuit protectionMains transient protectionCompliant to EMC EN61000-6-1 3Can house 2 batteries up to 12V 9Ah

GBP 72.44
1

Elmdene GEN3-08-A Switch Mode Power Supply Unit 1A

Elmdene GEN3-08-A Switch Mode Power Supply Unit 1A

Elmdene GEN3-08-A Switch Mode Power Supply Unit 1AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protection Electronic overload protection High security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warranty additional current for battery charging.Grade 3 Intruder systems.Mains Battery and PSU volt free fault outputs.Diagnostic LEDs.Lid rear tamper.Low quiescent battery standby current.Fit up to 7Ah battery. A Box 200h x 230w x 80d - Hinge lidPlease note The image is for illustrative purposes only. Please contact us for further information.

GBP 73.75
1