17 results (0,14494 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Cooper Fulleon 680004FULL-0027 Symphoni Voice Plus Sounder White W1 Housing

Cooper Fulleon 680004FULL-0027 Symphoni Voice Plus Sounder White W1 Housing

Cooper Fulleon 680004FULL-0027 Symphoni Voice Plus Sounder White W1 HousingAn Eaton Alarms signaling devices Fulleon Symphoni Voice Plus Sounder in White W1 housing. Voice message set VP015ASY Set to Tone 7Voice Message Set VP0Key FeaturesProduct Length Depth - 91 MmProduct Height - 105 MmProduct Width - 105 MmProduct Weight - .21 KgDegree Of Protection - Ip21Construction Material - Abs FrMaterial Housing - PlasticTones - 7Voice Tones - YesAddressing Mode - Hard AddressingSystem Topology - Conventional Non-AddressableType Of Current - Ad

GBP 76.81
1

Ziton DI-9301E Intelligent Addressable Single IO Module - 24VDC Monitor

Ziton DI-9301E Intelligent Addressable Single IO Module - 24VDC Monitor

Ziton DI-9301E Intelligent Addressable Single IO Module - 24VDC MonitorWith a microprocessor the DI-9301E Digital Single Input and Output Module the module can communicate with fire alarm control panel FACP check loop power-cut control output circuit faults logic state of input signals and state LEDs. On receiving start command from the FACP it will close the output relay and illuminate the active indicator.Key FeaturesThe dry contact input port can be programmed to NC or NO and monitoredThe input can also be programmed as self-answering which means that the Input port monitoring is disabled and the module will directly send a status signal to FACP when the dry-contact output changes stateAddressable unit. Address can be programmed in fieldInput port utilizes AD sampling technology for precise testingDIN-Rail mounted or Wall mountedStandard EN 54-182005

GBP 57.47
1

Advanced MXS-031-2T 2-Position Key Switch Trapped for MXP-045

Advanced MXS-031-2T 2-Position Key Switch Trapped for MXP-045

Advanced MXS-031-2T 2-Position Key Switch Trapped for MXP-045The 50 Way Network IO Card provides a convenient and cost-effective solution where multiple inputs and outputs are required.It is ideally suited for building control functions such as damperfan control or sprinkler control where onoffauto control and healthyfault or openclosed status indication is required.The inputs can be configured as a toggle switch or momentary push-button types.The outputs are fully programmable using the powerful dynamic cause and effects rules for output groups 1-50. In addition to the 50 IO circuits dedicated inputs and outputs are also provided.Status outputs include General Fire Fault Disablement and Test.A buzzer is also provided for audible annunciation of status changes. Inputs include buzzer mute momentary input enablereset and LED test. The 50-Way Network IO controller is a stand-alone unit withwithout its own EN54-4 power supply and charger.Each input and output on the card are fully programmable using a PC. An additional 100 LED outputs can be provided using the 100-way driver card output groups 101-200.Key FeaturesOver 50 programmable volt free switchpush button type inputs easily configured via our PC-NET-003 configuration software.Over 50 programmable LED driver outputs for energising and providing LED indication.Large colour graphical indication for site maps building layouts or simply zonal indication.Remote location by simply adding the type of mimic interface onto the Ad-netAd-net Network.Supplementary graphical indicationZonal or fully programmable LED optionFully networkable3-year warranty as standard

GBP 66.13
1

Advanced MXS-031-3U 3-Position Key Switch Un-trapped for MXP-045

Advanced MXS-031-3U 3-Position Key Switch Un-trapped for MXP-045

Advanced MXS-031-3U 3-Position Key Switch Un-trapped for MXP-045The 50 Way Network IO Card provides a convenient and cost-effective solution where multiple inputs and outputs are required.It is ideally suited for building control functions such as damperfan control or sprinkler control where onoffauto control and healthyfault or openclosed status indication is required.The inputs can be configured as a toggle switch or momentary push-button types.The outputs are fully programmable using the powerful dynamic cause and effects rules for output groups 1-50. In addition to the 50 IO circuits dedicated inputs and outputs are also provided.Status outputs include General Fire Fault Disablement and Test.A buzzer is also provided for audible annunciation of status changes. Inputs include buzzer mute momentary input enablereset and LED test. The 50-Way Network IO controller is a stand-alone unit withwithout its own EN54-4 power supply and charger.Each input and output on the card are fully programmable using a PC. An additional 100 LED outputs can be provided using the 100-way driver card output groups 101-200.Key FeaturesOver 50 programmable volt free switchpush button type inputs easily configured via our PC-NET-003 configuration software.Over 50 programmable LED driver outputs for energising and providing LED indication.Large colour graphical indication for site maps building layouts or simply zonal indication.Remote location by simply adding the type of mimic interface onto the Ad-netAd-net Network.Supplementary graphical indicationZonal or fully programmable LED optionFully networkable3-year warranty as standard

GBP 66.13
1

Advanced MXS-031-2U 2-Position Key Switch Un-trapped for MXP-045

Advanced MXS-031-2U 2-Position Key Switch Un-trapped for MXP-045

Advanced MXS-031-2U 2-Position Key Switch Un-trapped for MXP-045The 50 Way Network IO Card provides a convenient and cost-effective solution where multiple inputs and outputs are required.It is ideally suited for building control functions such as damperfan control or sprinkler control where onoffauto control and healthyfault or openclosed status indication is required.The inputs can be configured as a toggle switch or momentary push-button types.The outputs are fully programmable using the powerful dynamic cause and effects rules for output groups 1-50. In addition to the 50 IO circuits dedicated inputs and outputs are also provided.Status outputs include General Fire Fault Disablement and Test.A buzzer is also provided for audible annunciation of status changes. Inputs include buzzer mute momentary input enablereset and LED test. The 50-Way Network IO controller is a stand-alone unit withwithout its own EN54-4 power supply and charger.Each input and output on the card are fully programmable using a PC. An additional 100 LED outputs can be provided using the 100-way driver card output groups 101-200.Key FeaturesOver 50 programmable volt free switchpush button type inputs easily configured via our PC-NET-003 configuration software.Over 50 programmable LED driver outputs for energising and providing LED indication.Large colour graphical indication for site maps building layouts or simply zonal indication.Remote location by simply adding the type of mimic interface onto the Ad-netAd-net Network.Supplementary graphical indicationZonal or fully programmable LED optionFully networkable3-year warranty as standard

GBP 66.13
1