1.727 results (0,14892 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Vimpex ELS2A4AO Loop Sounder with Shallow Base in White

Vimpex ELS2A4AO Loop Sounder with Shallow Base in White

Vimpex ELS2A4AO Loop Sounder with Shallow Base in WhiteInstalling a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial all sounders will remain operational in the event of a short-circuit or open circuit fault.Component parts are approved by LPCB to relevant parts of EN 54 and the system is fully compliant with BS 5839-1 using a single sounder loop. Use of the Vimpex Loop Sounder System will greatly increase the reliability of the sounder circuits and in many cases result in a saving in the amount of cable used.Each loop can accommodate up to 45 sounders. Suitable for use on both conventional and addressable fire alarm systems the system provides much greater protection against faults than the dual radial circuit arrangements commonly used.The Vimpex Loop Sounder System significantly enhances the reliability of any sounder system. With conventional radial circuits a single open or short circuit fault on a sounder circuit could result in the loss of at least half of the sounders in an area of a building.The Vimpex Loop Sounder System has been fully tested and approved by LPCB to relevant EN 54 standards - certificates are available on request. This system is detailed in BS 5839-12002A22008 clause 12.2.2 j and Fig 1b as an alternative to the use of dual radial circuits. A detailed application guide is available from Vimpex as is a system loop calculator.Each sounder is supplied with a bi-directional short-circuit isolator fitted within its base. In the event of a short circuit the isolators will activate and disconnect the faulty section of cable while reporting in monitoring mode the fault to the control panel. When the sounders are activated the loop is driven from both ends ensuring that all sounders will remain operational even in the event of a single short-circuit or open-circuit fault. Sounders and their isolator bases are installed just like any other conventional sounders on the twin core circuit.

GBP 42.43
1

Vimpex ELS3A6AO Loop Sounder with Deep Base IP66 in Red

Vimpex ELS3A6AO Loop Sounder with Deep Base IP66 in Red

Vimpex ELS3A6AO Loop Sounder with Deep Base IP66 in RedInstalling a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial all sounders will remain operational in the event of a short-circuit or open circuit fault.Component parts are approved by LPCB to relevant parts of EN 54 and the system is fully compliant with BS 5839-1 using a single sounder loop. Use of the Vimpex Loop Sounder System will greatly increase the reliability of the sounder circuits and in many cases result in a saving in the amount of cable used.Each loop can accommodate up to 45 sounders. Suitable for use on both conventional and addressable fire alarm systems the system provides much greater protection against faults than the dual radial circuit arrangements commonly used.The Vimpex Loop Sounder System significantly enhances the reliability of any sounder system. With conventional radial circuits a single open or short circuit fault on a sounder circuit could result in the loss of at least half of the sounders in an area of a building.The Vimpex Loop Sounder System has been fully tested and approved by LPCB to relevant EN 54 standards - certificates are available on request. This system is detailed in BS 5839-12002A22008 clause 12.2.2 j and Fig 1b as an alternative to the use of dual radial circuits. A detailed application guide is available from Vimpex as is a system loop calculator.Each sounder is supplied with a bi-directional short-circuit isolator fitted within its base. In the event of a short circuit the isolators will activate and disconnect the faulty section of cable while reporting in monitoring mode the fault to the control panel. When the sounders are activated the loop is driven from both ends ensuring that all sounders will remain operational even in the event of a single short-circuit or open-circuit fault. Sounders and their isolator bases are installed just like any other conventional sounders on the twin core circuit.

GBP 43.62
1

Vimpex VMIS2S-W Secure Mains Isolator Switch in White Surface 8A

Vimpex VMIS2S-W Secure Mains Isolator Switch in White Surface 8A

Vimpex VMIS2S-W Secure Mains Isolator Switch in White Surface 8AThis product provides a secure method for safely isolating the mains voltage supply to fire systems in accordance with BS 5839 Part 1 2017.The unit is supplied in a complete enclosure which is a standard single gang format with preformed holes for mounting on a surface or 20 mm conduit box.The unit can be accessed by rectangular surface trunking. Please follow the latest IET electrical wiring practices when installing the product.Key FeaturesBoth the Live and Neutral supply is switchedIntegral fuse which cannot be removed without taking the cover offThe supply can only be isolated by an authorised person by means of a keylock switchThe key is removable in both ONOFF positionsWhen in the OFF position the FUSE is disconnected from the supplyPlease note The image is purely for illustrative purposes only.

GBP 24.66
1

Vimpex VMIS2F-W Secure Mains Isolator Switch in White Flush 8A

Vimpex VMIS2F-W Secure Mains Isolator Switch in White Flush 8A

Vimpex VMIS2F-W Secure Mains Isolator Switch in White Flush 8AThis product provides a secure method for safely isolating the mains voltage supply to fire systems in accordance with BS 5839 Part 1 2017.The unit is supplied in a complete enclosure which is a standard single gang format with preformed holes for mounting on a surface or 20 mm conduit box.The unit can be accessed by rectangular surface trunking. Please follow the latest IET electrical wiring practices when installing the product.Key FeaturesBoth the Live and Neutral supply is switchedIntegral fuse which cannot be removed without taking the cover offThe supply can only be isolated by an authorised person by means of a keylock switchThe key is removable in both ONOFF positionsWhen in the OFF position the FUSE is disconnected from the supplyPlease note The image is purely for illustrative purposes only.

GBP 23.42
1

RGL Electronics KP-LOCKBOX Lockable Keypad Box in White Finish

RGL Electronics KP-LOCKBOX Lockable Keypad Box in White Finish

RGL Electronics KP-LOCKBOX Lockable Keypad Box in White FinishThis lockable keypad box from RGL is made of mild steel with a white finish for securely housing installations.The internal place is pre-drilled so it is suitable for a number of control panel keypads.Key FeaturesLockable keypad boxInternal plate is pre-drilled to suit a number of control panel keypads2 keys suppliedKey removable in both positionsWhite powder coatedHinged lid

GBP 39.89
1

KAC K21SGS-12 Green Single Pole - Key Captive In 1 Position

KAC K21SGS-12 Green Single Pole - Key Captive In 1 Position

KAC K21SGS-12 Green Single Pole - Key Captive In 1 PositionThe KACK21SGS-12 is a green key switch call point. The keyis captive in one position.Key switch call points has broad temperature tolerance. Itis a robust switching device comprises a main housing and escutcheon plate. Itis fitted to the plate which simply snaps into the main housing and ispermanently located in place with fixing screws. All key switches are suppliedwith 2 sturdy keys. It has many applications like fire security smoke ventextinguishing systems and many other specialist applications.Key FeaturesColour Green

GBP 29.83
1

Zeta MKII-AHFI Fyreye MKII Addressable Fixed Heat Detector with Built In Isolator

Zeta MKII-AHFI Fyreye MKII Addressable Fixed Heat Detector with Built In Isolator

Zeta MKII-AHFI Fyreye MKII Addressable Fixed Heat Detector with Built In IsolatorThe Fyreye MKII Rate of Rise heat detector with built in isolator MKII-AHRI uses a thermistor arrangement to sense a quick rise in temperature and also a final threshold temperature of 57C.The Fyreye fixed heat detector with built in isolator MKII- AHFI has a single thermistor arrangement that gives an alarm at a temperature of 57C.Key FeaturesDesigned to meet EN54 requirementsRemote LED output8 LEDsLockable base

GBP 33.68
1

Haes Auxiliary Fused Relay in Red BRF248A-R

Haes Auxiliary Fused Relay in Red BRF248A-R

Haes Auxiliary Fused Relay in Red BRF248A-RA range of 24v nominal change over relay switches. The coil is polarised and suppressed and may be used on monitored circuits. The relays are suitable for a variety of low voltage and mains control and signalling purposes. The relays also are available fused un-fused red or white.Key Features8 amp double pole relaySuitable for mains switchingIndividually fused outputs on fused versionRed LED to indicate relay activated

GBP 22.64
1

RGL Electronics WP-KS-1 Covered Keyswitch Fitted In Stainless Steel Plate

RGL Electronics WP-KS-1 Covered Keyswitch Fitted In Stainless Steel Plate

RGL Electronics WP-KS-1 Covered Keyswitch Fitted In Stainless Steel PlateThe WP-KS-1 is a waterproof key switch with latching operation.This key switch is fitted in a stainless steel plate and built into a shrouded high-impact plastic back box with security screws. It is suitable for surface or flush mounting with the provided screw footprints.It has an easy clean surface and can handle more than one million operations making it a good fit for external fitting in public areas and hospitals. Two keys are provided with this latching key switch.Key FeaturesIP65 RatedLatching OnOff operationGasketgland includedKey removal in both positionsKeyed alike 2 x keys 2803Voltage free contactsNONC contacts 1 million operationsEtched legendSecurity screwsIP65 Rated - WeatherproofFunctional designEasy to operateUse for secure overrideEasy clean surface ideal for hospitalspublic areasScrew footprint for surface fitting onto standard back boxFootprint for mounting onto flush back box

GBP 35.76
1

RGL Electronics KS-1 Key Switch Fitted In Stainless Steel Plate

RGL Electronics KS-1 Key Switch Fitted In Stainless Steel Plate

RGL Electronics KS-1 Key Switch Fitted In Stainless Steel PlateThe KS-1 is a key switch with latching operation.This key switch is fitted in a stainless steel plate and built into a shrouded high-impact plastic back box with security screws. It is suitable for surface or flush mounting with the provided screw footprints.It has an easy clean surface and can handle more than one million operations making it a good fit for public areas and hospitals. Two keys are provided with this latching key switch.Key FeaturesLatching OnOff operationKey removal in both positionsSupplied with 2 x keysVoltage free contactsNONC contacts 1 million operationsEtched legendSecurity screwsFunctional designEasy to operateUse for secure overrideEasy clean surface ideal for hospitalspublic areasScrew footprint for surface fitting onto standard back boxFootprint for mounting onto flush back boxDimensions 85x85x5040 mm HxWxD

GBP 20.47
1

Morley K20SRS-11 Indoor Key Switch Red Key Removable in Both Positions Single Pole

Morley K20SRS-11 Indoor Key Switch Red Key Removable in Both Positions Single Pole

Morley K20SRS-11 Indoor Key Switch Red Key Removable in Both Positions Single PoleKAC Callpoints are the leaders in Call Point manufacture invented by KAC over 40 years ago they have constantly driven to improve both standards and design of the call point to this day.Key FeaturesProven reliability with a feature set that offers significantbenefits to the customerCertified to EN54 Part 11Single PoleKey removable in both positions

GBP 35.11
1

Vesda Xtralis 25mm In-line Expansion Socket 100mm PIP-019

Vesda Xtralis 25mm In-line Expansion Socket 100mm PIP-019

Vesda Xtralis 25mm In-line Expansion Socket 100mm PIP-019These sockets are used in the installation of pipework where buildings may contract or expand or have fluctuation of temperatures. They allow for movement within the pipework while maintaining a sealed connection due to the internal rubber gaskets.VESDA Aspirating Pipe and Fittings are produced in red ABS under a stringent quality control system approved to BS EN ISO 9001 EN54 - 20 and EN61386-1 Class 1131 ABS Acrylonitrile Butadiene Styrene is a robust polymer which has the most suitable physical properties for aspirating detection optimising performance with tensile strength chemical resistance ductility weatherability heat stability and processability.The range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system. They are also manufactured to comply with the requirements of BS5391 Part 1 EN 61386-1 and the new EN54 Part 20 guaranteeing you the quality you are used to as a VESDA customer.Key Features Tech SpecsMaterial ABSColour RedOperating temperature range -40C to 70CLength 100mmEN54 testedPlease Note The PIP-019 is equivalent to the REDEXSOC.

GBP 19.73
1

KAC K30SYS-33 Yellow Single Pole - Key Removable In All Positions - Firemans Vent

KAC K30SYS-33 Yellow Single Pole - Key Removable In All Positions - Firemans Vent

KAC K30SYS-33 Yellow Single Pole - Key Removable In All Positions - Firemans VentThe KACK30SYS-33 is a yellow key switch call point. Key removable in all positions.Key switch call points has broad temperature tolerance. Itis a robust switching device comprises a main housing and escutcheon plate. Itis fitted to the plate which simply snaps into the main housing and ispermanently located in place with fixing screws. All key switches are suppliedwith 2 sturdy keys. It has many applications like fire security smoke ventextinguishing systems and many other specialist applications.Key FeaturesColour YellowMarkings Firemans Vent

GBP 32.59
1

KAC K20SYS-11 Yellow Single Pole - Key Removable In All Positions - Plain Marking

KAC K20SYS-11 Yellow Single Pole - Key Removable In All Positions - Plain Marking

KAC K20SYS-11 Yellow Single Pole - Key Removable In All Positions - Plain MarkingThe KAC K20SYS-11 is a yellow key switch call point. The keyis removeable in all positions.Key switch call points has broad temperature tolerance. Itis a robust switching device comprises a main housing and escutcheon plate. Itis fitted to the plate which simply snaps into the main housing and ispermanently located in place with fixing screws. All key switches are suppliedwith 2 sturdy keys. It has many applications like fire security smoke ventextinguishing systems and many other specialist applications.Key FeaturesColour YellowPlain Markings

GBP 29.83
1

KAC K21SAS-11 Orange Single Pole - Key Captive In 1 Position - Plain Marking

KAC K21SAS-11 Orange Single Pole - Key Captive In 1 Position - Plain Marking

KAC K21SAS-11 Orange Single Pole - Key Captive In 1 Position - Plain MarkingThe KAC K21SAS-11 is an orange key switch call point. The keyis captive in one position.Key switch call points has broad temperature tolerance. Itis a robust switching device comprises a main housing and escutcheon plate. Itis fitted to the plate which simply snaps into the main housing and ispermanently located in place with fixing screws. All key switches are suppliedwith 2 sturdy keys. It has many applications like fire security smoke ventextinguishing systems and many other specialist applications.Key FeaturesColour OrangePlain Markings

GBP 30.49
1