82 results (0,14536 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP Relay Output Card as per CFP762 8 outputs per zone relays CFP763An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote and eight output per zone relays.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Output per zone relays will changeover when the corresponding zone is in alarm subject to certain conditions - for full details refer to the instructions downloadable below.Outputs are NOT designed to switch mains voltages.

GBP 67.02
1

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 Way

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 Way

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 WayThe C-Tec CA737 is a loop powered 4-8 way flat interface for use on the C-TEC EVAC-ALERT system. It is supplied as a 4-circuit unit extendable to 8 using CA737PCBDetailsA loop-powered 4-8 way flat interface for use on a C-TEC EVAC-ALERT systemSupplied as a 4 circuit unit extendable to 8 using a CA737PCB.Provides 4 or 8 monitored 12.5mA sounder circuits to power up to 2 self-testing evacuation alert sounders per flatIncludes space and connections for an optional fully monitored auxiliary 24V 1A CA737PSU to power additional visual indicators andor vibrating pillow padsIncludes an onboard short circuit loop isolatorUses one loop address per 4 sounder circuitsSounder circuit test facility per circuitThe most practical and flexible device interfacing method for most new and refurb installations the unit is ideally mounted in a riser on each floorMaintains the independent open short circuit monitoring of all sounder circuits

GBP 340.12
1

C-Tec CA739 CAST 4 Way Sounder Controller Extendable To 8 Way ZFP ONLY

C-Tec CA739 CAST 4 Way Sounder Controller Extendable To 8 Way ZFP ONLY

C-Tec CA739 CAST 4 Way Sounder Controller Extendable To 8Way ZFP ONLYA 4-8 way sounder controller specifically designed for useon a C-TEC CAST ZFP addressable fire alarm system.Compatible with C-TECs CAST ZFP Addressable Fire Panels.This device is NOT compatible with CAST XFP panels.Key FeaturesSupplied as a 4 circuit unit extendable to 8 circuits usinga CA739PCBProvides 4 or 8 monitored 12.5mA sounder circuitsIncludes space and connections for an optional fullymonitored auxiliary 24V 1.5A CA739PSU to power additional devicesIncludes an onboard short circuit loop isolatorUses one loop address per 4 sounder circuits12.5mA per sounder circuit capacity when loop powered 300mAper sounder circuit capacity when aux CA739PSU PSU is usedMaintains the independent open short circuitmonitoring of all sounder circuits

GBP 171.24
1

C-Tec SAP501EX SAP 1 Loop 16 Zone Addressable Sprinkler Monitoring Panel

C-Tec SAP501EX SAP 1 Loop 16 Zone Addressable Sprinkler Monitoring Panel

C-Tec SAP501EX SAP 1 Loop 16 Zone Addressable Sprinkler Monitoring PanelIdeal for monitoring up to 126 sprinkler flow switches.One switch monitoring unit required per monitored flow switch.Utilises the same technology asC-TECspopular XFP addressable fire panel.Up to 16 sprinkler zone indicators availableassignable via the panels PC programming tools.Attractiveflush or surface mountable plastic enclosure.Combined keypad or keyswitch entry.

GBP 455.02
1

C-Tec QTS25 Quantec Surveyor2 IOT Card cw 12 Months Surveyor2 Access

C-Tec QTS25 Quantec Surveyor2 IOT Card cw 12 Months Surveyor2 Access

C-Tec QTS25 Quantec Surveyor2 IOT Card cw 12 Months Surveyor2 AccessQuantec Surveyor2 IOT Card cw 12 months Surveyor2 access Includes IOT connection card web browser access emailable reports up to 5 mobile device connections for pushSMS messaging. 1 x QTS25 per Quantec Controller must be firmware rev 10A9 or above.Anew secure remote Cloud based data management software solution for C-TECs Quantec Addressable Call System.One QTS25 IOT card pictured required per Quantec Controller. Once connected provides 12 months access to ourSurveyor2 monitoring service yearly renewalfeeapplies see Order Codes Pricingtab below.Allows detailed reports on all aspects of call system activity to be accessed onsite or offsite via aninternet browser.Price includes5user accounts with full mobile device connectivity.User configurable dashboards Key Performance Indicator settings and remote access capabilities.Providesvaluable information on call history busiest shifts staff response times busiest rooms and more.Ideal for evaluating staff performance patient demands and determining labour levelsshift patterns.

GBP 783.10
1

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor UnitAllows IO devices that may not be compatible with the PSUfailure requirements of BS 7273-4 Cat A to comply.Is supplied on a single gang plate with an onboard isolatingEnd of Line Unit EOL and normally energised 24V 3A rated relay.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for all compatible IO units.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for multiple coincidental loop failures sometimes required in aspecification above and beyond the requirements of BS 7273-4 for allcompatible IO units.Key FeaturesAccommodates IO units sited inside or outside the 24V Auxenclosure IO units sited remotely require a BF390 EOL unit to maintain thefailsafe functionProvides complete galvanic isolation between the fire alarmsystem and the door release systemProvides where allowed failsafe manual door releasemonitoring to BS 7273-4 Cat A utilising a single TE cable for multiplemanual operating points such as free swing doors

GBP 26.46
1

C-Tec SAP501ECA SAP Sprinkler Panel 1 Loop 16z CAST

C-Tec SAP501ECA SAP Sprinkler Panel 1 Loop 16z CAST

C-Tec SAP501ECA SAP Sprinkler Panel 1 Loop 16z CASTA 1 loop SAP Sprinkler Panel on the CAST protocol.Key FeaturesIdeal for monitoring up to 255 sprinkler flow switchesOne CAST CA730 input output unit required per monitored flowswitchUtilises the same technology as C-TECs popular XFPaddressable fire panelUp to 16 sprinkler zone indicators available assignable viathe panels PC programming toolsAttractive flush or surface mountable plastic enclosureCombined keypad or keyswitch entry

GBP 416.69
1

C-Tec BF877QAQS 40 Character Alpha Pocket Pager - Vibrate

C-Tec BF877QAQS 40 Character Alpha Pocket Pager - Vibrate

C-Tec BF877QAQS 40 Character Alpha Pocket Pager - VibrateA 40 character Alpha Pocket Pager.This compact hand-held device allows you to receive updates directly in your pocket displaying up to 40 characters per message. Ideal for busy professionals who need to stay connected this pager is a must-have for efficient and reliable communication. Dont miss out on important alerts grab your C-Tec pager today and stay ahead of the curveKey FeaturesIncludes vibrate feature

GBP 240.48
1

C-Tec EP210F Flush Remote Status Unit

C-Tec EP210F Flush Remote Status Unit

C-Tec EP210F Flush Remote Status UnitThe remote status unit is designed to connect to the RS485 terminals on an EP203 Automatic Extinguisher Panel toprovide remote system status indicationviaa 128 x 64 pixel LCD status display.Also includes a pull-down manual release button a mode automanual keyswitch and a wide range of system status indicators.Key FeaturesThree monitored input connections Hold Abort and ModelMax. 8 remote status units per EP203 panelSurfaceremote status unitsEP210S and weather proof enclosures BF3591 also available

GBP 202.14
1

C-Tec CFP Network Driver Card CFP761

C-Tec CFP Network Driver Card CFP761

C-Tec CFP Network Driver Card CFP761An optional system expansion device for use with CFP Standardand CFPAlarmSense conventional fire panels.This part must be used if you require the use of a repeater panel or you wish to network compatible XFP panels together.Key FeaturesAllows the connection of up to eight CFP760 Repeaters one CFP761 required per Main all CFP760 repeaters include a CFP761 as standardCommunicates over screened two-wire fire resistant cableTotal repeater network cable length should not exceed 1KM

GBP 61.67
1

C-Tec NC805AS Air Switch

C-Tec NC805AS Air Switch

C-Tec NC805AS Air SwitchThe NC805AS is designed for use with C-TECsNC805P Pneumatic Pad. Applying pressure to the NC805P operates the airswitch which in turn triggers a Standard call when the 6.35mm jack plug on the NC805ASis connected to a compatible call points remote socket.Key FeaturesOperates at a minimum differential air pressure of 0.9 p.s.i pounds per square inch or 6220 Pa pascals 10 at 16CIP Rating IP20Ideal for patients who find it difficult to press buttons

GBP 106.18
1

C-Tec EP210S Surface Remote Status Unit

C-Tec EP210S Surface Remote Status Unit

C-Tec EP210S Surface Remote Status UnitThe remote status unit is designed to connect to the RS485 terminals on an EP203 Automatic Extinguisher Panel toprovide remote system status indicationviaa 128 x 64 pixel LCD status display.Also includes a pull-down manual release button a mode automanual keyswitch and a wide range of system status indicators.Key FeaturesThree monitored input connections Hold Abort and Mode.Max. 8 remote status units per EP203 panel.Flush remote status unitsEP210F and weather proof enclosures BF3591 also available.

GBP 209.29
1

C-Tec QT302RXSW Quantec Slave Infrared Ceiling Receiver White

C-Tec QT302RXSW Quantec Slave Infrared Ceiling Receiver White

C-Tec QT302RXSW Quantec Slave Infrared Ceiling Receiver WhiteThe Quantec Slave Infrared Ceiling Receiver connects to amaster Quantec infrared receiving device to increase IR coverage. It acceptsinfrared calls from compatible Quantec staff attack transmitters patientneckwrist pendants and staff attendance pendants.Key FeaturesTypically used in bedrooms corridors common rooms and anyother area requiring extended infrared coverageTypical 10m line of sight receiving rangeUp to three QT302RXS slave receivers can be used per masterPlease note The image is for illustrative purposes only. This product will come in the colour white.

GBP 64.69
1

C-Tec CFP704-2 CFP Two Wire 4 Zone AlarmSense Control Panel

C-Tec CFP704-2 CFP Two Wire 4 Zone AlarmSense Control Panel

C-Tec CFP Two Wire 4 Zone AlarmSense Control Panel - CFP704-2C-TECs LPCB certified two-wire CFP AlarmSense fire panel is designed to work with Apollos AlarmSense range of detectors call points sounders and beacons. Most conventional fire systems are designed to work with two pairs of wires per zone one pair for detection devices such as smoke detectors heat detectors and manual call points the other for alarm devices such as bells sounders or strobes. By using different voltage bands for quiescent and alarm states AlarmSense components can be connected to the same pair of supply wires.When powered and controlled by the CFP two-wire fire panel this reliable technology takes all the complexity out of fire alarm system design leading to quicker less expensive and more flexible installation. Indeed research shows an AlarmSense two-wire system can achieve a 20-25 reduction of labour over a standard four wire conventional system. AlarmSense devices are acceptable for BS 5839-1 and BS 5839-6 systems making them particularly useful for fire protection in Houses of Multiple Occupation HMOs.Key FeaturesLPCB certified to EN54 parts 2 and 4Intuitive user-friendly interface with colour-coded buttons and combined keypadkeyswitch entry to access level 22 4 or 8 AlarmSense zone circuits dependent on model purchasedFour conventional sounder circuitsIntegral 1.5A EN54-4A2 compliant switch mode PSUWide range of engineering functions including zone test coincidence zone delay and non- latching zonesTwo on-board relays Fire and FaultTwo open-collector outputs Remote and ResetClass change and alert inputsInstaller-friendly design accommodates easy first fix and straightforward maintenanceAttractive flush or surface mountable plastic lid and enclosure - no bezel requiredLow quiescent currentMultiple indicatorsEnd of line units included one per zoneAncillary system expansion connections provided for up to eight two-wire repeaters one CFP761 network driver card required per system and optional CFP relay boardsSpace for two x 12V 3.3Ah VRLA batteries

GBP 226.68
1

C-Tec CFP708-2 CFP Two Wire 8 Zone AlarmSense Control Panel

C-Tec CFP708-2 CFP Two Wire 8 Zone AlarmSense Control Panel

C-Tec CFP Two Wire 8 Zone AlarmSense Control Panel - CFP708-2C-TECs LPCB certified two-wire CFP AlarmSense fire panel is designed to work with Apollos AlarmSense range of detectors call points sounders and beacons. Most conventional fire systems are designed to work with two pairs of wires per zone one pair for detection devices such as smoke detectors heat detectors and manual call points the other for alarm devices such as bells sounders or strobes. By using different voltage bands for quiescent and alarm states AlarmSense components can be connected to the same pair of supply wires.When powered and controlled by the CFP two-wire fire panel this reliable technology takes all the complexity out of fire alarm system design leading to quicker less expensive and more flexible installation. Indeed research shows an AlarmSense two-wire system can achieve a 20-25 reduction of labour over a standard four wire conventional system. AlarmSense devices are acceptable for BS 5839-1 and BS 5839-6 systems making them particularly useful for fire protection in Houses of Multiple Occupation HMOs.Key FeaturesLPCB certified to EN54 parts 2 and 4Intuitive user-friendly interface with colour-coded buttons and combined keypadkeyswitch entry to access level 22 4 or 8 AlarmSense zone circuits dependent on model purchasedFour conventional sounder circuitsIntegral 1.5A EN54-4A2 compliant switch mode PSUWide range of engineering functions including zone test coincidence zone delay and non- latching zonesTwo on-board relays Fire and FaultTwo open-collector outputs Remote and ResetClass change and alert inputsInstaller-friendly design accommodates easy first fix and straightforward maintenanceAttractive flush or surface mountable plastic lid and enclosure - no bezel requiredLow quiescent currentMultiple indicatorsEnd of line units included one per zoneAncillary system expansion connections provided for up to eight two-wire repeaters one CFP761 network driver card required per system and optional CFP relay boardsSpace for two x 12V 3.3Ah VRLA batteries

GBP 272.59
1