707 results (0,13583 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP Relay Output Card as per CFP762 8 outputs per zone relays CFP763An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote and eight output per zone relays.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Output per zone relays will changeover when the corresponding zone is in alarm subject to certain conditions - for full details refer to the instructions downloadable below.Outputs are NOT designed to switch mains voltages.

GBP 67.02
1

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 Way

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 Way

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 WayThe C-Tec CA737 is a loop powered 4-8 way flat interface for use on the C-TEC EVAC-ALERT system. It is supplied as a 4-circuit unit extendable to 8 using CA737PCBDetailsA loop-powered 4-8 way flat interface for use on a C-TEC EVAC-ALERT systemSupplied as a 4 circuit unit extendable to 8 using a CA737PCB.Provides 4 or 8 monitored 12.5mA sounder circuits to power up to 2 self-testing evacuation alert sounders per flatIncludes space and connections for an optional fully monitored auxiliary 24V 1A CA737PSU to power additional visual indicators andor vibrating pillow padsIncludes an onboard short circuit loop isolatorUses one loop address per 4 sounder circuitsSounder circuit test facility per circuitThe most practical and flexible device interfacing method for most new and refurb installations the unit is ideally mounted in a riser on each floorMaintains the independent open short circuit monitoring of all sounder circuits

GBP 340.12
1

C-Tec CA739 CAST 4 Way Sounder Controller Extendable To 8 Way ZFP ONLY

C-Tec CA739 CAST 4 Way Sounder Controller Extendable To 8 Way ZFP ONLY

C-Tec CA739 CAST 4 Way Sounder Controller Extendable To 8Way ZFP ONLYA 4-8 way sounder controller specifically designed for useon a C-TEC CAST ZFP addressable fire alarm system.Compatible with C-TECs CAST ZFP Addressable Fire Panels.This device is NOT compatible with CAST XFP panels.Key FeaturesSupplied as a 4 circuit unit extendable to 8 circuits usinga CA739PCBProvides 4 or 8 monitored 12.5mA sounder circuitsIncludes space and connections for an optional fullymonitored auxiliary 24V 1.5A CA739PSU to power additional devicesIncludes an onboard short circuit loop isolatorUses one loop address per 4 sounder circuits12.5mA per sounder circuit capacity when loop powered 300mAper sounder circuit capacity when aux CA739PSU PSU is usedMaintains the independent open short circuitmonitoring of all sounder circuits

GBP 171.24
1

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor UnitAllows IO devices that may not be compatible with the PSUfailure requirements of BS 7273-4 Cat A to comply.Is supplied on a single gang plate with an onboard isolatingEnd of Line Unit EOL and normally energised 24V 3A rated relay.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for all compatible IO units.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for multiple coincidental loop failures sometimes required in aspecification above and beyond the requirements of BS 7273-4 for allcompatible IO units.Key FeaturesAccommodates IO units sited inside or outside the 24V Auxenclosure IO units sited remotely require a BF390 EOL unit to maintain thefailsafe functionProvides complete galvanic isolation between the fire alarmsystem and the door release systemProvides where allowed failsafe manual door releasemonitoring to BS 7273-4 Cat A utilising a single TE cable for multiplemanual operating points such as free swing doors

GBP 26.46
1

C-Tec BF366 Isolatable Relay on a Plate 24v 5A

C-Tec BF366 Isolatable Relay on a Plate 24v 5A

C-Tec BF366 Isolatable Relay on a Plate 24v 5AThe BF366 is a double-pole 24V 5A polarised relay specifically designed for use in 24V fire alarm systems. It includes a key switch isolation facility allowing the relay operation to be temporarily disabled from the fire alarm signal during routine test and maintenance to prevent auto diallers water sprinklers roller shutters etc. from activating.Mountable on a 25mm flush or surface mount back box the relay is trigger able via a control panels open collector output or a standard polarised fire alarm sounder circuit. If connecting to a sounder circuit note that the relay will return to its normal state when the fire condition is cleared or silenced. Check with the approving authority that the proposed arrangement is acceptable prior to installation.Key FeaturesA 24V 5A polarised relay designed for use in 24V fire alarm systemsIncludes a keyswitch isolation facility allowing the relay operation to be temporarily disabled during routine test and maintenance to prevent auto diallers water sprinklers roller shutters etc. from activatingWhen isolated the units Isolated LED will flash and a warning beeper will sound every 8 seconds to ensure devices are not inadvertently left in the isolated stateRelay is triggerable via a control panels open collector output or a standard polarised fire alarm sounder circuit if connecting to a sounder circuit the relay will return to its normal state when the fire condition is cleared or silenced - check with the approving authority that this arrangement is acceptable prior to installationFits on standard UK 25mm flush or surface mount back boxes

GBP 23.32
1

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with Handset

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with Handset

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with HandsetAn attractive Type Afire telephoneoutstation cw telephone-style handset. Supplied in a durable lift key lockablered steel case. Ideal for use infire telephone and stadium marshalling applications. Allows stewards and fire marshalsto communicate with a SigTEL Master Controller and vice versa. Facilitatesreliable two-way communication in a fire emergency between a permanently manned control room and key points ofasite.Key FeaturesTrue duplex speechCan be surface mounted using a T-BEZ302 bezelMeets and exceeds the requirements of BS 5839-9 when correctly installed

GBP 245.40
1

C-Tec BF376 Relay on a Plate 24v 5A Single Gang

C-Tec BF376 Relay on a Plate 24v 5A Single Gang

BF376 Relay on a Plate 24v 5A Single GangThe BF376 is a general purpose double-pole polarised 24V 5A relay designed for use in 24V fire alarm systems. It incorporates a high intensity LED which illuminates red when the relay is active. It may be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets roller shutter doors etc.Please note if connecting to a sounder circuit the relay will return to its normal state when the fire condition is cleared or silenced. Check with the approving authority that the proposed arrangement is acceptable prior to installation. The relay can be mounted on 25mm flush or surface mount back boxes. Mains wiring if used should be provided in accordance with the current edition of the IEE Wiring Regs.16th.Ed.The general requirement for any mains supply to the BF376 is fixed wiring using three core cable not less than 1mm2 fed from an isolating switch fuse spur fused at 5A max. This should be exclusive to the BF376 and its load and be labelled accordingly. As an alternative to a switched fused spur any double pole isolating device with a contact separation of 3mm or greater which is fitted with suitable in-circuit protection devices and meets the appropriate national wiring regulations can be used.Technical InformationActivation current Typically 30mA 24VDCIndicators Red relay activated LEDConnections V -V Supply NC C NO SW1 SW2. Contact rating 24Vdc is 5A resistive 2A inductive Contact rating 240Vac is 5A resistive 2A inductiveProduct dimensions mm 85w x 85h x 27d mm can be mounted onto a standard UK 25mm single gang flush or surface back boxConstruction finish White PVC plate light grey label silver nickel contactsIP Rating IP40Weight 78gOperating temperature -10C to 60CKey FeaturesA general purpose double-pole polarised 24V 5A relay designed for use in 24V fire alarm systemsIncorporates a high intensity LED which illuminates red when the relay is activeCan be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets rollershutter doors etcCan be mounted on 25mm flush or surface mount back boxes

GBP 8.15
1

C-Tec EP210F Flush Remote Status Unit

C-Tec EP210F Flush Remote Status Unit

C-Tec EP210F Flush Remote Status UnitThe remote status unit is designed to connect to the RS485 terminals on an EP203 Automatic Extinguisher Panel toprovide remote system status indicationviaa 128 x 64 pixel LCD status display.Also includes a pull-down manual release button a mode automanual keyswitch and a wide range of system status indicators.Key FeaturesThree monitored input connections Hold Abort and ModelMax. 8 remote status units per EP203 panelSurfaceremote status unitsEP210S and weather proof enclosures BF3591 also available

GBP 202.14
1

C-Tec NC805AS Air Switch

C-Tec NC805AS Air Switch

C-Tec NC805AS Air SwitchThe NC805AS is designed for use with C-TECsNC805P Pneumatic Pad. Applying pressure to the NC805P operates the airswitch which in turn triggers a Standard call when the 6.35mm jack plug on the NC805ASis connected to a compatible call points remote socket.Key FeaturesOperates at a minimum differential air pressure of 0.9 p.s.i pounds per square inch or 6220 Pa pascals 10 at 16CIP Rating IP20Ideal for patients who find it difficult to press buttons

GBP 106.18
1

C-Tec EP210S Surface Remote Status Unit

C-Tec EP210S Surface Remote Status Unit

C-Tec EP210S Surface Remote Status UnitThe remote status unit is designed to connect to the RS485 terminals on an EP203 Automatic Extinguisher Panel toprovide remote system status indicationviaa 128 x 64 pixel LCD status display.Also includes a pull-down manual release button a mode automanual keyswitch and a wide range of system status indicators.Key FeaturesThree monitored input connections Hold Abort and Mode.Max. 8 remote status units per EP203 panel.Flush remote status unitsEP210F and weather proof enclosures BF3591 also available.

GBP 209.29
1

C-Tec CFP Network Driver Card CFP761

C-Tec CFP Network Driver Card CFP761

C-Tec CFP Network Driver Card CFP761An optional system expansion device for use with CFP Standardand CFPAlarmSense conventional fire panels.This part must be used if you require the use of a repeater panel or you wish to network compatible XFP panels together.Key FeaturesAllows the connection of up to eight CFP760 Repeaters one CFP761 required per Main all CFP760 repeaters include a CFP761 as standardCommunicates over screened two-wire fire resistant cableTotal repeater network cable length should not exceed 1KM

GBP 61.67
1

C-Tec BF877QAQS 40 Character Alpha Pocket Pager - Vibrate

C-Tec BF877QAQS 40 Character Alpha Pocket Pager - Vibrate

C-Tec BF877QAQS 40 Character Alpha Pocket Pager - VibrateA 40 character Alpha Pocket Pager.This compact hand-held device allows you to receive updates directly in your pocket displaying up to 40 characters per message. Ideal for busy professionals who need to stay connected this pager is a must-have for efficient and reliable communication. Dont miss out on important alerts grab your C-Tec pager today and stay ahead of the curveKey FeaturesIncludes vibrate feature

GBP 240.48
1

C-Tec BF320 24V BS 5446-3 Vibrating Pillow Pad

C-Tec BF320 24V BS 5446-3 Vibrating Pillow Pad

C-Tec BF320 24V BS 5446-3 Vibrating Pillow PadCan be used in conjunction with a BF320JP connection plate to warn the hearing impaired of a potential fire alarm or evacuation alert condition. Vibrates and pulses on and off when triggered as per the requirements of BS 5446-3 2015. Designed to be placed under a pillow to supplement the audible andor visual indication alerts provided by a systems sounders andor VADs. Wide10-30V DC voltage range means it can also be connected to many third-party connector plates subject to testing. Includes a 2m connection lead with a locking mini-XLR connector to prevent accidental removal. Includes a 6K8 end-of-line monitoring resistor for fire alarm system use - see instructions for monitoring options on other systems. Supersedes our old BF363 pillow pad.Key FeaturesCan be used in conjunction with aBF320JP connection plateto warnthe hearing impaired of a potential fire alarm or evacuation alert condition.Vibrates and pulses on and off when triggered as per the requirements of BS 5446-3 2015.Designed to be placed under a pillow to supplement the audible andor visual indication alertsprovided by a systems sounders andor VADs.Wide10-30V DC voltagerange means it can also be connected tomanythird-party connector plates subject to testing.Includes a 2m connection lead with a locking mini-XLR connector to prevent accidental removal.Includes a 6K8 end-of-line monitoring resistor for fire alarm system use - see instructions for monitoring options on other systems.Supersedes our old BF363 pillow pad.

GBP 24.16
1

C-Tec ZFP Multi-Path Fault Tolerant Network PCB

C-Tec ZFP Multi-Path Fault Tolerant Network PCB

C-Tec ZFP Multi-Path Fault Tolerant Network PCBAllows the interconnection of up to 64 ZFP Main Panels any mix and up to 64 ZFP Compact Controllers over a two-wire RS485 ring-wired multi-path fault-tolerant Hi-Net network. One ZHN required per ZFP Main Panel ZFP Compact Controllers include a ZHN PCB as standard.Key FeaturesRS485 ProtocolMax. cable length between nodes 1KMMax. cable length of entire network 128KMFor retrofits multiple ZHNs can be wired in a non-fault tolerant single-path network configuration Max. 8 nodes Max length of entire network must not exceed 1KM.

GBP 294.67
1