62 resultater (0,17824 sekunder)

Vis alle filtre

Merke

Farge

Butikk

Pris (EUR)

Vis alle

Nullstill filter

Produkter
Fra
Butikker

Viega Prestabo bend 45° 15 Steel/Galvanized 558260 - Trykkroer Beslag

Viega Prestabo bend 45° 15 Steel/Galvanized 558260 - Trykkroer Beslag

Press connector systems with press connectors and pipes made of non-alloy steel 1.0308 (E235), in acc. with EN 10305-3, externally galvanised with a zinc layer thickness of 8-15 m (blue chromatised).Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingRed symbol (to prevent confusion with Sanpress Inox (stainless steel) articles) »Not for drinking water installations«Sealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber),not resistant against hydrocarbon solvent, chlorinated hydrocarbon solvents, turpentine, petrol, FKM, dull blackDimensionsD38

NOK 95.00
1

Viega Prestabo bend 45° 42 Steel/Galvanized 558314 - Trykkroer Beslag

Viega Prestabo bend 45° 42 Steel/Galvanized 558314 - Trykkroer Beslag

Press connector systems with press connectors and pipes made of non-alloy steel 1.0308 (E235), in acc. with EN 10305-3, externally galvanised with a zinc layer thickness of 8-15 m (blue chromatised).Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingRed symbol (to prevent confusion with Sanpress Inox (stainless steel) articles) »Not for drinking water installations«Sealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber),not resistant against hydrocarbon solvent, chlorinated hydrocarbon solvents, turpentine, petrol, FKM, dull blackDimensionsD38

NOK 236.00
1

Viega Prestabo bend 45° 54 Steel/Galvanized 558321 - Trykkroer Beslag

Viega Prestabo bend 45° 54 Steel/Galvanized 558321 - Trykkroer Beslag

Press connector systems with press connectors and pipes made of non-alloy steel 1.0308 (E235), in acc. with EN 10305-3, externally galvanised with a zinc layer thickness of 8-15 m (blue chromatised).Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingRed symbol (to prevent confusion with Sanpress Inox (stainless steel) articles) »Not for drinking water installations«Sealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber),not resistant against hydrocarbon solvent, chlorinated hydrocarbon solvents, turpentine, petrol, FKM, dull blackDimensionsD38

NOK 307.00
1

Viega profipress g elbow 45° 35 345648 - Trykkroer Beslag

Viega profipress g elbow 45° 35 345648 - Trykkroer Beslag

Press connector system with press connectors and pipes made of copper in acc. with EN 1057 and DVGW worksheet GW 392 suitable for:Gases in acc. with DVGW G 260 in gas installations in acc. with DVGW-TRGI 2008 (DVGW worksheet G 600) / DVFG-TRF 2012Liquid gas in the gas phase for domestic and commercial applications, tested in acc. with DVGW worksheet G 5614Heating oil pipelines for heating oil in acc. with DIN 51603-1Diesel fuel pipelines for diesel fuel, as suction and pressure pipelines in acc. with EN 590 in consideration of the general technical approval Z-38.4-71Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet G 5614, point 4.4.1, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingYellow dot, yellow rectangle and inscription »Gas MOP 5 / GT1«Sealing elementsHNBR, yellowDimensions/MaterialStandard sizes: d 12, 15, 18, 22, 28, 35, 42, 54 made of copperXL sizes: d 64.0 made of copperPress connectors with threaded connection d 12-54 made of gunmetalXL press connectors with threaded connection d 64.0 made of copperAreas of applicationNatural gas/Liquid gasHeating oil/Diesel fuel (d 12-54)NoteOnly Viega copper and gunmetal press connectors, which are marked with a yellow rectangle and have the inscription »Gas MOP 5 / GT1« are permitted for use in installations for gas, heating oil and diesel fuel systems!Use of the system for application areas and media other than those described here must be agreed with Viega Service Center through a material request.Operating conditionsGas and liquid gas systemsOperating temperature -20 °C up to +70 °COperating pressure max. 0.5 MPaOperatin

NOK 325.00
1

Viega Raxofix bend 90° 32 gunmetal / glossy - Alu pex systemer

Viega Raxofix bend 90° 32 gunmetal / glossy - Alu pex systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 268.00
1

Viega Raxofix bend 90° 16 gunmetal / glossy - Alu pex systemer

Viega Raxofix bend 90° 16 gunmetal / glossy - Alu pex systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 123.00
1

Viega Terminal screw 16 x 1.8 mm gunmetal - PEX systemer

Viega Terminal screw 16 x 1.8 mm gunmetal - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 148.00
1

Viega Sealing flange 130 x 40 x 0.8 mm - PEX systemer

Viega Sealing flange 130 x 40 x 0.8 mm - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 78.00
1

Viega Raxofix bend 45° 25 gunmetal / glossy - Alu pex systemer

Viega Raxofix bend 45° 25 gunmetal / glossy - Alu pex systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 245.00
1

Viega Mounting bracket 150/160 mm - PEX systemer

Viega Mounting bracket 150/160 mm - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 131.00
1

Viega Clamp connection Combi PB 15 x 2.5 mm gunmetal - PEX systemer

Viega Clamp connection Combi PB 15 x 2.5 mm gunmetal - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 153.00
1

Viega Coupling PB 16 mm gunmetal - PEX systemer

Viega Coupling PB 16 mm gunmetal - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 217.00
1

Viega Raxofix bend 90° 20 gunmetal / glossy - Alu pex systemer

Viega Raxofix bend 90° 20 gunmetal / glossy - Alu pex systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 151.00
1

Viega Connection screw PB 16 mm x 3/4" gunmetal - PEX systemer

Viega Connection screw PB 16 mm x 3/4" gunmetal - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 173.00
1

Viega Transition piece PB 16 mm x 1/2" nipple gunmetal - PEX systemer

Viega Transition piece PB 16 mm x 1/2" nipple gunmetal - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 169.00
1

Viega Raxofix bend 90° 40 gunmetal / glossy - Alu pex systemer

Viega Raxofix bend 90° 40 gunmetal / glossy - Alu pex systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 507.00
1

Viega Transition piece PB 16 mm x 1/2" sleeve gunmetal - PEX systemer

Viega Transition piece PB 16 mm x 1/2" sleeve gunmetal - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 171.00
1

Viega Raxofix bend 90° 25 gunmetal / glossy - Alu pex systemer

Viega Raxofix bend 90° 25 gunmetal / glossy - Alu pex systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xcdimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xcflexible, blackDimensionsPress connectors and pipesRaxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installationsOperating temperature max. 70 °COperating pressure max. 1.0 MPaHeating installationsOperating temperature max. 80 °COperating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

NOK 205.00
1

Viega Distributor pipe 3/4" - 3 gunmetal - PEX systemer

Viega Distributor pipe 3/4" - 3 gunmetal - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpresse

NOK 541.00
1

Viega Distribution pipe 3/4" - 2 gunmetal - PEX systemer

Viega Distribution pipe 3/4" - 2 gunmetal - PEX systemer

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpresse

NOK 407.00
1

Viega Sanpress Inox transition fitting 22 x 3/4" Stainless steel/bright 437503 - Trykkroer Beslag

Viega Sanpress Inox transition fitting 22 x 3/4" Stainless steel/bright 437503 - Trykkroer Beslag

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

NOK 417.00
1

Viega Sanpress bend 45° 28 gunmetal/glossy 111670 - Trykkroer Beslag

Viega Sanpress bend 45° 28 gunmetal/glossy 111670 - Trykkroer Beslag

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

NOK 313.00
1

Viega Sanpress bend 90° 22 gunmetal/glossy 104818 - Trykkroer Beslag

Viega Sanpress bend 90° 22 gunmetal/glossy 104818 - Trykkroer Beslag

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

NOK 224.00
1

Viega Sanpress bend 45° 22 gunmetal/glossy 112004 - Trykkroer Beslag

Viega Sanpress bend 45° 22 gunmetal/glossy 112004 - Trykkroer Beslag

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

NOK 250.00
1

Viega Sanpress bend 90° 42 gunmetal/glossy 130497 - Trykkroer Beslag

Viega Sanpress bend 90° 42 gunmetal/glossy 130497 - Trykkroer Beslag

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

NOK 740.00
1