Promydea.it | Web Agency Sicilia

Apollo Discovery Marine Isolator Base 45681-211MAR

Apollo Discovery Marine Isolator Base 45681-211MARThe Discovery Marine Isolator Base is unique and designed to only accept the marine isolator.Key FeaturesComplies with the essential requirements of the EMC Directive 201430EU.Complies with the essential requirements of the Construction Products Regulation 3052011 EU.Complies with the essential requirements of the Marine Equipment Directive 201490EU.For use with the 55000-721MAR Discovery marine isolator

GBP 4.80

1

Haes TPCA13-FIL Filter PCB for Marine Panels

Haes TPCA13-FIL Filter PCB for Marine PanelsA Filter PCB designed for use with Marine Panels.

GBP 34.10

1

Hochiki Marine Common Mounting Base YBN-R3M

Hochiki Marine Common Mounting Base YBN-R3MModel YBN-R3 is a Common Mounting Base which is fully compatible with Hochikis Marine Approved ESP sensors. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if required.Key FeaturesElectronics freeSupports the ESP Marine Approved SensorsStainless steel contactsTakes 2.5 mm cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick Connection via square cable clampsApproved to MED by GL

GBP 3.36

1

Hochiki Marine Sensor Mounting Base YBN-R3MWHT

Hochiki Marine Sensor Mounting Base YBN-R3MWHTModel YBN-R3M is a Common Mounting Base which is fully compatible with Hochikis Marine Approved ESP sensors. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if requiredKey FeaturesElectronics freeSupports the ESP Marine Approved SensorsStainless steel contactsTakes 2.5 mm cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick Connection via square cable clampsApproved to MED by GL

GBP 3.36

1

Apollo Conventional Marine Waterproof Manual Call Point - 55100-022MAR

Apollo Conventional Marine Waterproof Manual Call Point - 55100-022MARThe Conventional Marine Waterproof Manual Call Point Red is a Type A call point suitable for outdoor use. The Conventional Marine Manual Call Point has been designed to operate on conventional marine fire detection systems. The Manual Call Point has an easily resettable element rather than a break glass.This call point is supplied with a backbox for surface mounting. It also features a unique Plug and Play installation concept designed specifically to reduce installation time. The call point utilises a terminal block where all installation cabling is terminated. The red Manual Call Point is approved to EN54-11 standard and Marine Equipment Directive 9698EC.Key FeaturesRed LED indicatorPlug and Play terminal connections for fast wiringResettable element

GBP 123.50

1

Apollo Orbis Marine TimeSaver Base ORB-MB-00001-MAR

Apollo Orbis Marine TimeSaver Base ORB-MB-00001-MARThe Orbis Marine TimeSaver Base provides installers with an open working area with fixing holes shaped to allow a simple mounting procedure. Orbis Marine conventional fire detectors offer a wealth of features to save time enhance reliability and reduce false alarms within the marine environment.These include drift compensation and DirtAlert a feature that warns Service Engineers via a flashing yellow LED that detectors need maintenance and patented FasTest a procedure that takes just four seconds to test smoke detectors and confirm that they are functioning correctly.Key FeaturesGrouped terminals to make wiring easyMultiple fixing centresLED alignment markCable stripping guideContinuity link for voltage testing of zone wiring prior to commissioningDetector locking mechanismBrand FeaturesApproved for use in marine environmentsModern low-profile designTimeSaver Base for fast installationTransient rejection for false alarm reductionHigh humidity tolerance at up to 98 RHWide operating temperature -40C to 70C

GBP 5.81

1

Kentec MK67000M1 Syncro View Marine Local LCD Repeater Panel

Kentec MK67000M1 Syncro View Marine Local LCD Repeater PanelThe Syncro View Marine fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Syncro ASM fire alarm control panel to other locations.The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Syncro ASM fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The Syncro View Marine is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro ASM control panel a maximum of 4 View Marine repeater panels in this combination or up to 15 View Marine repeater panels if powered local from an ancillary 24V DC supply or a 230V powered option with local battery back-up.Syncro View Marine is housed in a small enclosure which is styled similarly to the Syncro ASM control panel and is ideal for installations where a large fire control panel would be detrimental to dcor or where space is at a premium such as the Control Bridge or Helm.Up to 15 Syncro View Marine annunciators can be connected to each control panel on the Syncro ASM network making View Marine ideal where multiple points of indication andor control are required in such as places as engine rooms staff quarters living spaces or control areas.Key FeaturesUp to 15 annunciators can be connected to each Syncro ASM fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro ASM panel controlsSimple two-wire serial connectionSmall Syncro style enclosureRemovable electronics for easy installation24V DC or 230V AC power options

GBP 474.18

1

Apollo Discovery Marine Isolator 55000-721MAR

Apollo Discovery Marine Isolator 55000-721MARThe Discovery Marine Isolator is placed at intervals on the loop and ensures that in the case of a short-circuit only the section between the isolators will be affected. When the short-circuit is removed the isolators automatically restore power and data to the isolated section.Key FeaturesDetects wiring short-circuits using patented technologyMinimises disruption from short-circuitsAutomatic de-isolation on short-circuit removalUp to 20 detectors or equivalent load may be installed between isolators

GBP 30.83

1

Hochiki MCP1A Marine Conventional Manual Call Point

Hochiki MCP1A Marine Conventional Manual Call PointThe MCP1A is a Conventional Marine Approved call-point based upon the industry standard KAC world series housing and features easy to install push-fit wiring terminals. The unit features a Non Frangible Plastic element.Key FeaturesComplies with EN54-11Push-fit terminals can accommodate up to a 2.5mm2 solid conductorUnique Plug Play installation conceptRe-settable operating element optionResistive and clean contact connectionsSemi-flush or surface mountingBackward compatibilityApproved by GL

GBP 13.37

1

Apollo Orbis Marine Optical Smoke Detector ORB-OP-42001-MAR

Apollo Orbis Marine Optical Smoke Detector ORB-OP-42001-MARThe Orbis Marine Optical Smoke Detector operates on the well-established light scatter principle. However the sensing technology is radically different in design from previous optical detectors and significantly reduces false alarms. Orbis Marine conventional fire detectors offer a wealth of features to save time enhance reliability and reduce false alarms within the marine environment.These include drift compensation and DirtAlert a feature that warns Service Engineers via a flashing yellow LED that detectors need maintenance and patented FasTest a procedure that takes just four seconds to test smoke detectors and confirm that they are functioning correctly.Key FeaturesResponds well to fast-burning flaming firesReduced false alarmsIncreased reliability of detectionSensing chamber keeps out dust and other airborne contaminantsOperates over a broad range of voltages at extremes of temperatureBrand FeaturesApproved for use in marine environmentsModern low-profile designTimeSaver Base for fast installationTransient rejection for false alarm reductionHigh humidity tolerance at up to 98 RHWide operating temperature -40C to 70C

GBP 27.98

1

Apollo Discovery Marine Heat Detector 58000-400MAR

Apollo Discovery Marine Heat Detector 58000-400MARDiscovery Marine analogue addressable fire detectors are suitable for larger vessels. The high specification range has been developed to meet the requirements of sophisticated systems. Discovery gives you total reassurance in installations where it is necessary to adapt detection to different operating environments and where protection against unwanted alarms is paramount.The Discovery Marine Heat Detector uses a single thermistor to sense the air temperature at the detector position. The thermistor is connected in a resistor network which produces a voltage output dependent on temperature. The design of the resistor network together with the processing algorithm in the microcontroller gives an approximately linear characteristic from 10C to 80C. This lineariser signal is further processed depending on the response mode selected and converted to an analogue output.Key FeaturesApproved for use in the marine environmentFive response modes for environmental adaptationDaynight switching for increased flexibilityDrift compensation for false alarm reductionUser programmability for dataXPERT card addressing for increased securityIdeal in environments that are dirty or smokyUnaffected by wind or atmospheric pressureRemote test feature

GBP 64.84

1

Kentec MK67000AM1 Syncro View Marine Repeater 24v Flat Plate Fascia

Kentec MK67000AM1 Syncro View Marine Repeater 24v Flat Plate FasciaThe Syncro View Marine fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Syncro ASM fire alarm control panel to other locations.The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Syncro ASM fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The Syncro View Marine is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro ASM control panel a maximum of 4 View Marine repeater panels in this combination or up to 15 View Marine repeater panels if powered local from an ancillary 24V DC supply or a 230V powered option with local battery back-up.Syncro View Marine is housed in a small enclosure which is styled similarly to the Syncro ASM control panel and is ideal for installations where a large fire control panel would be detrimental to dcor or where space is at a premium such as the Control Bridge or Helm.Up to 15 Syncro View Marine annunciators can be connected to each control panel on the Syncro ASM network making View Marine ideal where multiple points of indication andor control are required in such as places as engine rooms staff quarters living spaces or control areas.Key FeaturesUp to 15 annunciators can be connected to each Syncro ASM fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro ASM panel controlsSimple two-wire serial connectionSmall Syncro style enclosureRemovable electronics for easy installation24V DC or 230V AC power options

GBP 499.58

1

Hochiki Marine Standard Ivory Mounting Base YBN-R6M

Hochiki Marine Standard Ivory Mounting Base YBN-R6MModel YBN-R6M is a Conventional Detector Mounting Base approved for marine applications by GL Germanischer Lloyd and is associated with the CDX Range of Marine Approved Detectors.It is supplied with square cable clamps for secure and reliable cable termination but the base does not provide line continuity during detector removal therefore if Call Points are being used then these should be wired onto the zone first. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputLow Profile only 8 mmRugged designElectronics freeQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectorsApproved to MED by GLGL Type approval

GBP 4.99

1

Apollo SA5900-928MAR Intelligent Marine Manual Call Point

Apollo SA5900-928MAR Intelligent Marine Manual Call PointThe Intelligent Marine Manual Call Point MCP has been designed to operate on a loop of intelligent fire detection devices. An alarm is initiated by pressing the resettable element. The MCP signals to the Fire Control Panel using an interrupt feature within the Apollo Digital Communication Protocol. An alarm status is indicated through the rotation of the resettable element displaying yellow and black indication bars and a solid red LED. The MCP can be easily reset from the front using the supplied reset key. The Intelligent Marine MCP is intended for indoor marine and offshore applications and has a built-in short circuit isolator.OperationThe address of each call point is set at the commissioning stage by means of a DIL switch. A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Marine Manual Call Point SIL Approved can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.The Intelligent Marine Manual Call Point incorporates a short circuit isolator which will ensure its operation in the event of a short circuit fault on the loop. Isolator operation is indicated by a solid yellow LED.Key FeaturesResettable element for testingEasy access front reset mechanismA unique ergonomically designedKey for resetting and front cover removal

GBP 53.21

1

Apollo Orbis Marine Relay Base ORB-RB-40004-MAR

Apollo Orbis Marine Relay Base ORB-RB-40004-MARThe Orbis Marine Relay Base incorporates a single-pole voltage-free changeover contact for switching ancillary equipment. When the detector changes to the alarm state the relay is energized causing the contact to change state. The contact will remain in this condition until the detector is reset.Brand InformationOrbis Marine conventional fire detectors offer a wealth of features to save time enhance reliability and reduce false alarms within the marine environment. These include drift compensation and DirtAlert a feature that warns Service Engineers via a flashing yellow LED that detectors need maintenance and patented FasTest a procedure that takes just four seconds to test smoke detectors and confirm that they are functioning correctly.Key FeaturesGrouped terminals to make wiring easyMultiple fixing centresLED alignment markCable stripping guideContinuity link for voltage testing of zone wiring prior to commissioningDetector locking mechanism

GBP 27.31

1

Apollo Orbis Marine A1R Heat Detector with Flashing LED ORB-HT-41013-MAR

Apollo Orbis Marine A1R Heat Detector with Flashing LED ORB-HT-41013-MARThe Orbis Marine Heat Detector uses a single thermistor to sense the air temperature around the detector. There are twelve heat detectors in the Orbis Marine range designed to suit a wide variety of operating conditions.Brand FeaturesOrbis Marine conventional fire detectors offer a wealth of features to save time enhance reliability and reduce false alarms within the marine environment. These include drift compensation and DirtAlert a feature that warns Service Engineers via a flashing yellow LED that detectors need maintenance and patented FasTest a procedure that takes just four seconds to test smoke detectors and confirm that they are functioning correctly.Key FeaturesCan be used for applications where smoke detectors are unsuitableIdeal for environments that are dirty or smoky under normal conditionsFlashing LED option

GBP 19.97

1

Apollo Orbis Marine BS Heat Detector with Flashing LED ORB-HT-41016-MAR

Apollo Orbis Marine BS Heat Detector with Flashing LED ORB-HT-41016-MARThe Orbis Marine Heat Detector uses a single thermistor to sense the air temperature around the detector. There are twelve heat detectors in the Orbis Marine range designed to suit a wide variety of operating conditions.Brand InformationOrbis Marine conventional fire detectors offer a wealth of features to save time enhance reliability and reduce false alarms within the marine environment. These include drift compensation and DirtAlert a feature that warns Service Engineers via a flashing yellow LED that detectors need maintenance and patented FasTest a procedure that takes just four seconds to test smoke detectors and confirm that they are functioning correctly.Key FeaturesCan be used for applications where smoke detectors are unsuitableIdeal for environments that are dirty or smoky under normal conditionsFlashing LED option

GBP 20.99

1

Apollo Conventional Marine Manual Call Point - 55100-021MAR

Apollo Conventional Marine Manual Call Point - 55100-021MARThe Conventional Marine Manual Call Point has been designed to operate on conventional marine fire detection systems. The Manual Call Point has an easily resettable element rather than a break glass. This call point is supplied with a backbox for surface mounting. It also features a unique Plug and Play installation concept designed specifically to reduce installation time. The call point utilises a terminal block where all installation cabling is terminated. The red Manual Call Point is approved to EN54-11 standard and Marine Equipment Directive 9698EC.The Manual Call Point consists of a 470ohm resistor in series with a normally open switch contact. The Manual Call Point helps reduce installation time as all the initial installation cabling is wired to a terminal block which connects neatly to the call point. Once activated the manual call point can be reset by inserting the test key into the bottom of the unit until the key clicks into position. Remove the test key and push the front cover up until it clicks home.

GBP 21.49

1

Apollo Marine DIN-Rail Switch Monitor Plus 55000-772MAR

Apollo Marine DIN-Rail Switch Monitor Plus 55000-772MARThe Marine DIN-Rail Switch Monitor Plus is designed to monitor the state of one or more single pole volt free contacts connected on a single pair of cables and to report the status to Apollo compatible analogue control equipment. In addition it incorporates additional circuitry to monitor flow switches and provide a time delay in so doing. It also contains circuitry which can be used to reset a beam detector.OperationThe Marine DINRail switch monitor provides four input states to the control equipment normal fault pre-alarm and alarm. The unit has a red LED to indicate an alarm and a yellow LED to indicate a fault condition. The Marine DINRail switch monitor is loop-powered and operates at 1728V DC with protocol voltage pulses of 59V. The unit is designed to accept a maximum line resistance of 50ohm. The end-of-line resistor required is 20k ohm.

GBP 75.87

1

Apollo Marine DIN-Rail Zone Monitor 55000-773MAR

Apollo Marine DIN-Rail Zone Monitor 55000-773MARThe Marine DINRail Zone Monitor powers and controls the operation of a zone of up to 20 conventional fire detectors from a loop of XP95 addressable detectors and ancillary devices.OperationThis unit needs to be installed in a suitable enclosure and secured using end stops part no 27447-528 or equivalent. The Marine DINRail zone monitor is factory pre-set to return an analogue value of 16 when all detectors on the zone are in the quiescent state and 64 when a detector changes to the alarm state.The unit latches in the alarm state. A 5.1K end-of-line resistor is used to monitor cables for open and short-circuit faults. Alternatively an active end-of-line monitor may be used in conjunction with diode bases and a capacitor of up to 50F fitted at the unit wiring terminals. In either case an analogue value of 4 is transmitted during open or short-circuit faults.The Marine DINRail zone monitor is fitted with a bi-directional short-circuit isolator and will be unaffected by loop short-circuits on either loop input or output.Key FeaturesLoop-poweredVisible short-circuitLED Built in isolator

GBP 112.91

1

Apollo Discovery Marine Manual Call Point with Isolator 58100-971MAR

Apollo Discovery Marine Manual Call Point with Isolator 58100-971MARThe Discovery Marine Manual Call Point has been approved for use in indoor marine applications. A seven-segment DIL switch enables addressing of each call point at commissioning stage. When operated the manual call point interrupts the polling cycle for a fast response. Bi-coloured LEDs indicate isolate and normal conditions.OperationThe Discovery Marine Manual Call Point MCP is based on the KAC conventional MCP range. It is electronically and mechanically compatible with previous Apollo call points based on KACs World Series product. The address of each call point is set at the commissioning stage by means of a seven-segment DIL switch. If a MCP is activated it interrupts the normal protocol to give a fast response.Key FeaturesFlashing LED option to indicate polling Discovery systems onlyPlug and Play terminal connections for fast wiringContinuity link for wiring test before commissioningReports an alarm in under 0.2 secondsResettable element

GBP 99.68

1

Cranford Control 511-156 Sounder Beacons MED amp ABS Approved - White - Blue LED - 24VDC - Deep - Outdoors amp Indoors

Cranford Control 511-156 Sounder Beacons MED ABS Approved - White - Blue LED - 24VDC - Deep - Outdoors IndoorsIntroducing the Cranford Controls Marine Wall Sounder Flashing LED Beacon - Deep Base - White Body Blue Lens - 511-156.Our VTB EN54-3-approved sounderbeacon has been meticulously engineered to cater to the demanding conditions of marine environments. Building on its reliable performance we have further enhanced its capabilities to meet the unique requirements of marine applications.Equipped with 32 sounder tones including commonly used patterns and two specialized marine tones the 511-156 ensures effective signalling in any situation. The added marine-specific tones are designed to enhance safety and communication in maritime settings.To complement your specific needs we offer a choice between white or red body colour options and a range of lens colours to suit different applications.Choose the Cranford Controls Marine Wall Sounder Flashing LED Beacon - Deep Base - 511-156 and experience top-notch reliability and performance in marine signalling.Product FeaturesApproved to Marine Equipment Directive 201490EU Inc. IEC 60092-504 IEC 60533 EN 54-3EMC testing to IEC 60533-Electrical and electronic installations in shipsEnvironmental testing to IEC 60092-504-Installations in ships Controls and instrumentation32 Selectable tonesIndustry-specific Marine General Alarm tone and IMO Code 2 Continuous signalAlert to evacuation changeover via the third wireProtection rating BS EN 60529 Deep-based variants IP65Designed to work with Marine-approved fire alarm systemsTwist and lock bayonet mounting systemLens colour options-Red Amber Clear Blue and GreenABS Fire retardant plastic

GBP 49.62

1

Hochiki WCP1A Marine Conventional Weatherproof Call Point

Hochiki WCP1A Marine Conventional Weatherproof Call PointTheWCP1A is a Conventional marine-approved weather-proof call-point based upon the industry standard KAC World Series housing and features easy to install push-fit wiring terminals.The unit can support either a Frangible Glass element or a Non Frangible Plastic element and features a weather-proof Housing to IP67 which means it can be mounted in the most severe environmental conditions without water ingress.Key FeaturesApproved to EN54-112001Terminals can accommodate up to a 2.5 mm solid conductorIngress Protection rated to IP67Approved to MED by GLGL Type ApprovalApproved by LPCB

GBP 95.89

1

Hochiki YBN-R3MSCI Marine Approved Short Circuit Isolator Base Ivory

Hochiki YBN-R3MSCI Marine Approved Short Circuit Isolator Base IvoryThe Hochiki YBN-R3MSCI is a marine-approved sensor mounting base featuring an integral short-circuit isolator which will detect and isolate short-circuits on the loop. When a short-circuit is detected during power up the unit will drop the power to the rest of the loop.The base is compatible with the ESP range of marine-approved sensors and does not require a loop address. A remote fire LED facility is provided when a sensor is attached to the base.NOTE A fitted sensor will still be powered when this device is isolating.Key FeaturesFeatures integral SCIEasy to fitSlim profileMatches standard sensor and base colours

GBP 19.19

1

Apollo Discovery Marine Waterproof Manual Call Point with Isolator 58100-976MAR

Apollo Discovery Marine Waterproof Manual Call Point with Isolator 58100-976MARThe Discovery Marine Manual Call Point has been approved for use in outdoor marine applications. A seven-segment DIL switch enables addressing of each call point at commissioning stage. When operated the manual call point interrupts the polling cycle for a fast response. Bi-coloured LEDs indicate isolate and normal conditions.OperationThe Discovery Marine Waterproof Manual Call Point MCP is based on the KAC conventional MCP range. It is electronically and mechanically compatible with previous Apollo call points based on KACs World Series product. The address of each call point is set at the commissioning stage by means of a seven-segment DIL switch. If a MCP is activated it interrupts the normal protocol to give a fast response.Key FeaturesPlug and Play terminal connections for fast wiringContinuity link for wiring test before commissioningReports an alarm in under 0.2 secondsResettable element

GBP 252.16

1

Realizziamo gli obiettivi di business dei nostri clienti: dicci cosa ti serve, lo realizzeremo per te.

Brand

Merchant

Price (EUR)