18 results (0,14655 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APO

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APO

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APOAll detectors in the Soteria XP95 and Discovery range fit into the XPERT 8 Intelligent Mounting Base.The base has a wide interior diameter for ease of access to cables and terminals. The E-Z Fit feature allows you to fit the base screws place the XPERT 8 Intelligent Mounting Base over the screws slide it into place and tighten the screws.The detector requires a clockwise rotation into the base for fitting. Additionally the detector can be locked into the base for increased security by a grub-screw using a 1.5mm hexagonal driver.The XPERT 8 card part number 38532-064 supplied with the base has pre-punched pips to remove to set the address. Refer to the Coding Guide for details on how to set the address.Backwards CompatibilitySoteria detectors have been designed to operate on XP95 and Discovery loops. This allows for Soteria detectors and bases to operate on existing systems and for Soteria detectors to operate on XP95 and Discovery bases XPERT 7 Intelligent Mounting Base. It should be noted that not all features of Soteria will be available when used with XP95 or Discovery fire control panels. If Soteria detectors are used with XP95 fire control panels incorporating drift compensation algorithms these must be disabled when communicating with Soteria devices.When Soteria detectors are used with an XPERT 7 Intelligent Mounting Base on a CoreProtocol system Soteria devices will have a 128 address offset due to only 7 address pips being available on the XPERT 7 card. For example an XPERT 7 card set at 32 will address as 160 on CoreProtocol with Soteria detectors.Key FeaturesCompatibility with Soteria XP95 and Discovery detectorsIsolated and Non-isolated devices supportedIsolated wiper - maintains loop connectivity during temporary removal of devicesXPERT 8 card for Core-ProtocolE-Z Fit allows for simple mounting of the detector base after wiringKeyed to accept only addressable devicesBase mark allows for LED detector alignmentPlease Note XPERT 8 card increase the address capacity to 254 when using Soteria detector and Core-Protocol enabled fire control panel.

GBP 2.64
1

Hochiki Standard Base YBN-R3 Ivory

Hochiki Standard Base YBN-R3 Ivory

Hochiki Standard Base YBN-R3 IvoryModel YBN-R3 is a Common Mounting Base which is fully compatible with Hochikis ESP sensors beacons base sounders and VADs.It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if required.Key FeaturesElectronics freeSupports the ESP SensorsStainless steel contactsTakes 2.5 mm cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick Connection via square cable clamps

GBP 2.18
1

Hochiki Standard Mounting Base YBN-R3WHT White

Hochiki Standard Mounting Base YBN-R3WHT White

Hochiki Standard Mounting Base YBN-R3WHT WhiteModel YBN-R3WHT is a Common Mounting Base which is fully compatible with Hochikis ESP range of sensors beacons base sounders and VADs. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if required.Key FeaturesElectronics freeStainless steel contactsTakes 2.5 mm cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick Connection via square cable clampsAlso available in ivory and black

GBP 2.18
1

Hochiki Marine Sensor Mounting Base YBN-R3MWHT

Hochiki Marine Sensor Mounting Base YBN-R3MWHT

Hochiki Marine Sensor Mounting Base YBN-R3MWHTModel YBN-R3M is a Common Mounting Base which is fully compatible with Hochikis Marine Approved ESP sensors. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if requiredKey FeaturesElectronics freeSupports the ESP Marine Approved SensorsStainless steel contactsTakes 2.5 mm cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick Connection via square cable clampsApproved to MED by GL

GBP 3.36
1

Hochiki Marine Common Mounting Base YBN-R3M

Hochiki Marine Common Mounting Base YBN-R3M

Hochiki Marine Common Mounting Base YBN-R3MModel YBN-R3 is a Common Mounting Base which is fully compatible with Hochikis Marine Approved ESP sensors. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if required.Key FeaturesElectronics freeSupports the ESP Marine Approved SensorsStainless steel contactsTakes 2.5 mm cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick Connection via square cable clampsApproved to MED by GL

GBP 3.36
1

C-Tec S-KEY Spare Key for CFP Panels

C-Tec S-KEY Spare Key for CFP Panels

C-Tec S-KEY Spare Key for CFP PanelsA spare plastic S-KEY for use C-TECs CFP XFP and ZFP fire panels.Key FeaturesProvides authorised users with access to a fire panels authorised user controlsFinished in red polycarbonate for extra strengthSuitable for use with the C-Tecs CFP 2-8 zone standard economy and AlarmSense fire panels C-Tecs XFP 1 Loop 16 Zone panel and C-Tecs full range of ZFP multi-loop addressable fire panelsDimensions 47w x 25h x 9d mmRed polycarbonate

GBP 1.93
1

Apollo 45682-860APO Black XPERT Universal Address Card Pack of 10

Apollo 45682-860APO Black XPERT Universal Address Card Pack of 10

Apollo 45682-860APO Black XPERT Universal Address Card Pack of 10The Universal XPERT Address Card has been designed to allow the same card to be used on both XPERT 7 XPERT 8 bases.AddressingTo set an address using the XPERT Universal Address Card you have to remove the pips using a screwdriver. The pips are designated with numbers. Each removed pip is added together to provide the final address.Key FeaturesAddress pips have additional lead-in for a higher toleranceSimplifies and speeds up installation and commissioningAddress remains the same no matter how often the detectors are replacedIncludes 128th pip for CoreProtocol systems

GBP 4.06
1

Hochiki YBV-R4WHT Mounting Base for SCI Sensors - White

Hochiki YBV-R4WHT Mounting Base for SCI Sensors - White

Hochiki YBV-R4WHT Mounting Base for SCI Sensors - WhiteThe YBV-R4WHT is an SCI Sensor Mounting Base which is fully compatible with Hochikis ESP range of SCI sensors. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if required.Please note This base does not provide short-circuit isolation on its own but allows the SCI sensor range to operate with SCI functionality.Key FeaturesElectronics freeStainless steel contactsTakes 2.5mm2 cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick connection via square cable clampsFourth terminal allows for SCI functionality of sensorsColour White

GBP 4.36
1

Hochiki YBV-R4 Base

Hochiki YBV-R4 Base

Hochiki YBV-R4 BaseModel YBV-R4 is an SCI Sensor Mounting Base which is fully compatible with Hochikis ESP range of SCI sensors. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if required.Please note This base does not provide short-circuit isolation on its own but allows the SCI sensor range to operate with SCI functionality.Key FeaturesElectronics freeStainless steel contactsTakes 2.5mm2 cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick connection via square cable clampsFourth terminal allows for SCI functionality of sensors

GBP 4.36
1

Hochiki Conventional White Mounting Base YBN-R6WHT

Hochiki Conventional White Mounting Base YBN-R6WHT

Hochiki Conventional White Mounting Base YBN-R6WHTModel YBN-R6WHT is a Conventional Detector Mounting Base associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels.It is supplied with square cable clamps for secure and reliable cable termination but the base does not provide line continuity during detector removal therefore if Call Points are being used then these should be wired onto the zone first. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputLow Profile only 8 mmRugged design and electronics freeQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectorsAlso available in ivory or black

GBP 2.10
1

Hochiki YBN-R6BLK Conventional Mounting Base Black

Hochiki YBN-R6BLK Conventional Mounting Base Black

Hochiki YBN-R6BLK Conventional Mounting Base BlackModel YBN-R6BLK is a Conventional Detector Mounting Base associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels. It is supplied with square cable clamps for secure and reliable cable termination but the base does not provide line continuity during detector removal therefore if Call Points are being used then these should be wired onto the zone first. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputLow Profile only 8 mmRugged design and electronics freeQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectorsAlso available in white or ivory

GBP 4.19
1

Hochiki Conventional Standard Mounting Base YBN-R6 Ivory

Hochiki Conventional Standard Mounting Base YBN-R6 Ivory

Hochiki Conventional Standard Mounting Base YBN-R6 IvoryModel YBN-R6 is a Conventional Detector Mounting Base associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels.It is supplied with square cable clamps for secure and reliable cable termination but the base does not provide line continuity during detector removal therefore if Call Points are being used then these should be wired onto the zone first. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputLow Profile only 8 mmRugged design and electronics freeQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectorsAlso available in white or black

GBP 2.10
1

Hochiki Conventional Schottky Base YBN-R6SK Ivory

Hochiki Conventional Schottky Base YBN-R6SK Ivory

Hochiki Conventional Schottky Base YBN-R6SK IvoryModel YBN-R6SK is a Conventional Detector Mounting Base with in-line Schottky Diode associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels.It is supplied with square cable clamps for secure and reliable cable termination and the base provides line continuity during detector removal. Therefore Call Points can be wired in any order on the zone providing a suitable panel and End Of Line EOL unit is used. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputIn-line Schottky Diode for Line ContinuityLow Profile only 8 mmRugged designQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectors

GBP 3.11
1