294 results (0,14726 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Vimpex ELS2A4AO Loop Sounder with Shallow Base in White

Vimpex ELS2A4AO Loop Sounder with Shallow Base in White

Vimpex ELS2A4AO Loop Sounder with Shallow Base in WhiteInstalling a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial all sounders will remain operational in the event of a short-circuit or open circuit fault.Component parts are approved by LPCB to relevant parts of EN 54 and the system is fully compliant with BS 5839-1 using a single sounder loop. Use of the Vimpex Loop Sounder System will greatly increase the reliability of the sounder circuits and in many cases result in a saving in the amount of cable used.Each loop can accommodate up to 45 sounders. Suitable for use on both conventional and addressable fire alarm systems the system provides much greater protection against faults than the dual radial circuit arrangements commonly used.The Vimpex Loop Sounder System significantly enhances the reliability of any sounder system. With conventional radial circuits a single open or short circuit fault on a sounder circuit could result in the loss of at least half of the sounders in an area of a building.The Vimpex Loop Sounder System has been fully tested and approved by LPCB to relevant EN 54 standards - certificates are available on request. This system is detailed in BS 5839-12002A22008 clause 12.2.2 j and Fig 1b as an alternative to the use of dual radial circuits. A detailed application guide is available from Vimpex as is a system loop calculator.Each sounder is supplied with a bi-directional short-circuit isolator fitted within its base. In the event of a short circuit the isolators will activate and disconnect the faulty section of cable while reporting in monitoring mode the fault to the control panel. When the sounders are activated the loop is driven from both ends ensuring that all sounders will remain operational even in the event of a single short-circuit or open-circuit fault. Sounders and their isolator bases are installed just like any other conventional sounders on the twin core circuit.

GBP 44.11
1

Vimpex ELS3A6AO Loop Sounder with Deep Base IP66 in Red

Vimpex ELS3A6AO Loop Sounder with Deep Base IP66 in Red

Vimpex ELS3A6AO Loop Sounder with Deep Base IP66 in RedInstalling a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial all sounders will remain operational in the event of a short-circuit or open circuit fault.Component parts are approved by LPCB to relevant parts of EN 54 and the system is fully compliant with BS 5839-1 using a single sounder loop. Use of the Vimpex Loop Sounder System will greatly increase the reliability of the sounder circuits and in many cases result in a saving in the amount of cable used.Each loop can accommodate up to 45 sounders. Suitable for use on both conventional and addressable fire alarm systems the system provides much greater protection against faults than the dual radial circuit arrangements commonly used.The Vimpex Loop Sounder System significantly enhances the reliability of any sounder system. With conventional radial circuits a single open or short circuit fault on a sounder circuit could result in the loss of at least half of the sounders in an area of a building.The Vimpex Loop Sounder System has been fully tested and approved by LPCB to relevant EN 54 standards - certificates are available on request. This system is detailed in BS 5839-12002A22008 clause 12.2.2 j and Fig 1b as an alternative to the use of dual radial circuits. A detailed application guide is available from Vimpex as is a system loop calculator.Each sounder is supplied with a bi-directional short-circuit isolator fitted within its base. In the event of a short circuit the isolators will activate and disconnect the faulty section of cable while reporting in monitoring mode the fault to the control panel. When the sounders are activated the loop is driven from both ends ensuring that all sounders will remain operational even in the event of a single short-circuit or open-circuit fault. Sounders and their isolator bases are installed just like any other conventional sounders on the twin core circuit.

GBP 45.36
1

Vimpex VMIS2F-W Secure Mains Isolator Switch in White Flush 8A

Vimpex VMIS2F-W Secure Mains Isolator Switch in White Flush 8A

Vimpex VMIS2F-W Secure Mains Isolator Switch in White Flush 8AThis product provides a secure method for safely isolating the mains voltage supply to fire systems in accordance with BS 5839 Part 1 2017.The unit is supplied in a complete enclosure which is a standard single gang format with preformed holes for mounting on a surface or 20 mm conduit box.The unit can be accessed by rectangular surface trunking. Please follow the latest IET electrical wiring practices when installing the product.Key FeaturesBoth the Live and Neutral supply is switchedIntegral fuse which cannot be removed without taking the cover offThe supply can only be isolated by an authorised person by means of a keylock switchThe key is removable in both ONOFF positionsWhen in the OFF position the FUSE is disconnected from the supplyPlease note The image is purely for illustrative purposes only.

GBP 24.36
1

Vimpex VMIS2S-W Secure Mains Isolator Switch in White Surface 8A

Vimpex VMIS2S-W Secure Mains Isolator Switch in White Surface 8A

Vimpex VMIS2S-W Secure Mains Isolator Switch in White Surface 8AThis product provides a secure method for safely isolating the mains voltage supply to fire systems in accordance with BS 5839 Part 1 2017.The unit is supplied in a complete enclosure which is a standard single gang format with preformed holes for mounting on a surface or 20 mm conduit box.The unit can be accessed by rectangular surface trunking. Please follow the latest IET electrical wiring practices when installing the product.Key FeaturesBoth the Live and Neutral supply is switchedIntegral fuse which cannot be removed without taking the cover offThe supply can only be isolated by an authorised person by means of a keylock switchThe key is removable in both ONOFF positionsWhen in the OFF position the FUSE is disconnected from the supplyPlease note The image is purely for illustrative purposes only.

GBP 25.63
1

Vimpex Fire-Cryer Plus FC3AW0D in White Deep Base

Vimpex Fire-Cryer Plus FC3AW0D in White Deep Base

Vimpex Fire-Cryer Plus FC3AW0D in White Deep BaseThe Fire-Cryer Plus requires no special wiring and can be retrofitted to existing installations. They are fully synchronised and have an exceptionally low current consumption. The units can be used as a replacement for electronic sounders or bells to broadcast a clear message for any situation - evacuation chemical spills access message security or general information.The Fire-Cryer Plus is a wall mounted voice enhanced sounder alarm unit. This product is ideal for use on fire alarm systems.The Fire-Cryer comes in an attractive white colour which makes it ideal for areas where red sounder units are not suitable.This device comes supplied with an IP66 rated deep base which means that it is ideal for use in external locations or areas where high levels of moisture may be present in the environment.Key FeaturesSound output - 100 dBAOptional integral strobe - red lens with red LED or clear lens with dual white and amber LEDsLow current - average 20 mANo special wiring easily retro-fittedFully synchronised over multi-zonesDeep base version available to IP667 user-definable messages from a library of hundredsApproved to EN 54-3

GBP 97.96
1

Vimpex DHBFS24 Brass Door Holder in Flush Mount 200N 24Vdc

Vimpex DHBFS24 Brass Door Holder in Flush Mount 200N 24Vdc

Vimpex DHBFS24 Brass Door Holder in Flush Mount 200N 24VdcThese attractive door holders are ideal for prestigious installations which demand high spec. fittings. These units available in chrome stainless steel or brass-look finishes are supplied with release buttons and with matching keeper plates.These magnets fit directly to a standard single-gang electrical back box which enables the unit to be easily flush-mounted. If surface mounting is necessary then colour-matched kits can be used to conceal the surface mounted box. These are supplied with two 20mm entry holes and blanking plugs. Comes with switch.

GBP 120.95
1

Vimpex Fire-Cryer Plus FC3AW0S in White Shallow Base

Vimpex Fire-Cryer Plus FC3AW0S in White Shallow Base

Vimpex Fire-Cryer Plus FC3AW0S in White Shallow BaseThe Fire-Cryer Plus requires no special wiring and can be retrofitted to existing installations. They are fully synchronised and have an exceptionally low current consumption. The units can be used as a replacement for electronic sounders or bells to broadcast a clear message for any situation - evacuation chemical spills access message security or general information.The Fire-Cryer Plus is a wall mounted voice enhanced sounder alarm unit. This product is ideal for use on fire alarm systems.The Fire-Cryer comes in an attractive white colour which makes it ideal for areas where red sounder units are not suitable.Key FeaturesSound output - 100 dBAOptional integral strobe - red lens with red LED or clear lens with dual white and amber LEDsLow current - average 20 mANo special wiring easily retro-fittedFully synchronised over multi-zonesDeep base version available to IP667 user-definable messages from a library of hundredsApproved to EN 54-3

GBP 97.96
1

Vimpex CBE1002-C Conventional Ceiling Mount VAD with Base in White C3-7.5

Vimpex CBE1002-C Conventional Ceiling Mount VAD with Base in White C3-7.5

Vimpex CBE1002-C Conventional Ceiling Mount VAD with Base in White C3-7.5A high intensity ceiling-mounted Visual Alarm Device the unit is ideal for providing a primary warning signal in areas where sounders alone will not be sufficient.Installation of the product is by use of a standard detector base which is included in your purchase. The VAD23 - Ceiling Mounted Beacon is third party approved to EN54-23 and certified to the rating of C-3-7.5.Key FeaturesLow power high output LED technologyCoverage radius of 7.5 m when installed at a ceiling height of 3 mFlash rate of 0.5 Hz 1 every 2 secondsAnti-tamper lock to prevent unauthorised removal3rd Party Approved EN 54-23Easy central cable entry5 Year WarrantyUtilises a standard detector base IncludedHigh intensity clear LED

GBP 56.06
1

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-R

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-R

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-RThe IS-mA1 is a compact 100dBA alarm sounder. Approvals include ATEX IECEx and GOST-R for Zone 0 applications and FM approval for Class I Division 1 and Class I Zone 0 applications.It is suitable for all intrinsically safe signalling applications including fire security and process control.Key FeaturesInput overload and reverse current protectionEnd of line resistor certifiedAuto synchronised sound outputAvailable with custom tone configurationsGroup1 Mining

GBP 247.62
1

Vimpex Fire-Cryer Plus FC3AWRD Red Beacon Deep Base IP66 in White

Vimpex Fire-Cryer Plus FC3AWRD Red Beacon Deep Base IP66 in White

Vimpex Fire-Cryer Plus FC3AWRD Red Beacon Deep Base IP66 in WhiteThe Fire-Cryer Plus requires no special wiring and can be retrofitted to existing installations. They are fully synchronised and have an exceptionally low current consumption. The units can be used as a replacement for electronic sounders or bells to broadcast a clear message for any situation - evacuation chemical spills access message security or general information. The strobe is not intended to be the primary source of alarm and a such has not been assessed for compliance to EN 54-23.The Fire-Cryer Plus is a combined voice sounder and flashing beacon unit ideal for use on fire safety system.This device is designed to emit an audible voice message on activation of the fire alarm system.In addition to the voice message this device also activates the integral flashing beacon to give a visual alarm signal this is ideal in helping to comply with DDA regulations.Key FeaturesSound output - 100 dBAOptional integral strobe - red lens with red LED or clear lens with dual white and amber LEDsLow current - average 20 mANo special wiring easily retro-fittedFully synchronised over multi-zonesDeep base version available to IP667 user-definable messages from a library of hundredsApproved to EN 54-3

GBP 123.01
1

Vimpex Identifire IDBTS-W White Base Sounder with Cover

Vimpex Identifire IDBTS-W White Base Sounder with Cover

Vimpex Identifire IDBTS-W White Base Sounder with CoverThe slimmest sounder in its class the Vimpex Base Sounder supplies true omni-directional sound output and is fully compatible with the other sounders in the range. The sounder comes with 32 user-selectable tones incorporating low frequencies high frequencies European American and Australian normsand all industry-standard frequency patterns.Tested and approved to EN 54 Part 3 the Identifire Base Sounder fits neatly under any ceiling mounted fire detector or can be mounted stand-alone with the use of a front blanking plate.Key Features32 TonesEN 54-3 tested and fully approved in accordance with CPRSlimmest profile in the industryLow current consumptionOmni-directional soundFront plate for stand-alone use availableFour selectable volume levelsInstaller friendly terminalsCeiling or wall mountingRobust and easily connected two in two out 2.5mm terminals

GBP 18.95
1

Vimpex Loop Sounder with Short Circuit Isolator ELS2A6AO

Vimpex Loop Sounder with Short Circuit Isolator ELS2A6AO

Vimpex Loop Sounder with Short Circuit Isolator ELS2A6A0Installing a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial all sounders will remain operational in the event of a short-circuit or open circuit fault.Component parts are approved by LPCB to relevant parts of EN 54 and the system is fully compliant with BS 5839-1 using a single sounder loop. Use of the Vimpex Loop Sounder System will greatly increase the reliability of the sounder circuits and in many cases result in a saving in the amount of cable used.Each loop can accommodate up to 45 sounders. Suitable for use on both conventional and addressable fire alarm systems the system provides much greater protection against faults than the dual radial circuit arrangements commonly used.The Vimpex Loop Sounder System significantly enhances the reliability of any sounder system. With conventional radial circuits a single open or short circuit fault on a sounder circuit could result in the loss of at least half of the sounders in an area of a building.Each sounder is supplied with a bi-directional short-circuit isolator fitted within its base. In the event of a short circuit the isolators will activate and disconnect the faulty section of cable while reporting in monitoring mode the fault to the control panel. When the sounders are activated the loop is driven from both ends ensuring that all sounders will remain operational even in the event of a single short-circuit or open-circuit fault. Sounders and their isolator bases are installed just like any other conventional sounders on the twin core circuit.Key FeaturesApproved to EN 54

GBP 44.11
1

Vimpex SG-S-W-32 SmartGuard - Surface Mount White - 32mm Spacer

Vimpex SG-S-W-32 SmartGuard - Surface Mount White - 32mm Spacer

Vimpex SG-S-W-32 SmartGuard - Surface Mount White - 32mm SpacerThe SG-S-W-32 is a white SmartGuard with a 32mm spacer.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour WhiteSurface Mount32mm Spacer

GBP 31.20
1

Vimpex SG-S-Y-32 SmartGuard - Surface Mount Yellow - 32mm Spacer

Vimpex SG-S-Y-32 SmartGuard - Surface Mount Yellow - 32mm Spacer

Vimpex SG-S-Y-32 SmartGuard - Surface Mount Yellow - 32mm SpacerThe SG-S-Y-32 is a yellow SmartGuard with a 32mm spacer.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour YellowSurface Mount32mm Spacer

GBP 31.20
1

Vimpex SG-SS-Y-32 SmartGuard - Surface Mount Sounder Yellow - 32mm Spacer

Vimpex SG-SS-Y-32 SmartGuard - Surface Mount Sounder Yellow - 32mm Spacer

Vimpex SG-SS-Y-32 SmartGuard - Surface Mount Sounder Yellow - 32mm SpacerThe SG-SS-Y-32 is a yellow SmartGuard with a 32mm spacer and sounder.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour YellowSurface Mount32mm Spacer

GBP 64.08
1

Vimpex SG-S-B-32 SmartGuard - Surface Mount Blue - 32mm Spacer

Vimpex SG-S-B-32 SmartGuard - Surface Mount Blue - 32mm Spacer

Vimpex SG-S-B-32 SmartGuard - Surface Mount Blue - 32mm SpacerThe SG-S-B-32 is a blue SmartGuard with a 32mm spacer.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour BlueSurface Mount32mm Spacer

GBP 31.20
1

Vimpex SG-S-R-32 SmartGuard - Surface Mount Red - 32mm Spacer

Vimpex SG-S-R-32 SmartGuard - Surface Mount Red - 32mm Spacer

Vimpex SG-S-R-32 SmartGuard - Surface Mount Red - 32mm SpacerThe SG-S-R-32 is a red SmartGuard with a 32mm spacer.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour RedSurface Mount32mm Spacer

GBP 31.20
1

Vimpex SG-S-G-32 SmartGuard - Surface Mount Green - 32mm Spacer

Vimpex SG-S-G-32 SmartGuard - Surface Mount Green - 32mm Spacer

Vimpex SG-S-G-32 SmartGuard - Surface Mount Green - 32mm SpacerThe SG-S-G-32 is a green SmartGuard with a 32mm spacer.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour GreenSurface Mount32mm Spacer

GBP 31.20
1

Vimpex SG-SS-G-32 SmartGuard - Surface Mount Sounder Green - 32mm Spacer

Vimpex SG-SS-G-32 SmartGuard - Surface Mount Sounder Green - 32mm Spacer

Vimpex SG-SS-G-32 SmartGuard - Surface Mount Sounder Green - 32mm SpacerThe SG-SS-G-32 is a green SmartGuard with a 32mm spacer and sounder.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour GreenSurface Mount32mm SpacerPlease note The image is for illustrative purposes only.

GBP 64.08
1

Vimpex SG-SS-R-32 SmartGuard - Surface Mount Sounder Red - 32mm Spacer

Vimpex SG-SS-R-32 SmartGuard - Surface Mount Sounder Red - 32mm Spacer

Vimpex SG-SS-R-32 SmartGuard - Surface Mount Sounder Red - 32mm SpacerThe SG-SS-R-32 is a red SmartGuard with a 32mm spacer and sounder.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour RedSurface Mount32mm SpacerPlease note The image is for illustrative purposes only.

GBP 64.08
1

Vimpex SG-SS-W-32 SmartGuard - Surface Mount Sounder White - 32mm Spacer

Vimpex SG-SS-W-32 SmartGuard - Surface Mount Sounder White - 32mm Spacer

Vimpex SG-SS-W-32 SmartGuard - Surface Mount Sounder White - 32mm SpacerThe SG-SS-W-32 is a white SmartGuard with a 32mm spacer and sounder.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour WhiteSurface Mount32mm SpacerPlease note The image is for illustrative purposes only.

GBP 64.08
1

Vimpex SG-SS-B-32 SmartGuard - Surface Mount Sounder Blue - 32mm Spacer

Vimpex SG-SS-B-32 SmartGuard - Surface Mount Sounder Blue - 32mm Spacer

Vimpex SG-SS-B-32 SmartGuard - Surface Mount Sounder Blue - 32mm SpacerThe SG-SS-B-32 is a blue SmartGuard with a 32mm spacer and sounder.Misuse of manual call points or pull stations resulting in false or nuisance alarms is a costly and troublesome interruption to business continuity. BS 5839 The British Standard for Fire Alarm Installations recommends the use of manual call point covers in vulnerable areas to mitigate against false alarms.Our Smart products have proven success in reducing unwanted false alarm incidents. Watch our video to see products in application.Key FeaturesDesigned for ease of installation the SmartGuard can be fitted in minutesAn optional battery powered 90dB alarm can be fitted increasing the security and protection of the device it is coveringA break seal can also be fitted to increase the visible deterrent against misuseColour BlueSurface Mount32mm SpacerPlease note The image is for illustrative purposes only.

GBP 64.08
1

Vimpex PF-Z728 Zener Barrier - 1 Channel

Vimpex PF-Z728 Zener Barrier - 1 Channel

Vimpex PF-Z728 Zener Barrier - 1 ChannelThe Zener Barrier prevents the transfer of unacceptably high energy from the safe area into the hazardous area. The zener diodes in the Zener Barrier are connected in the reverse direction. The breakdown voltage of the diodes is not exceeded in normal operation. If this voltage is exceeded due to a fault in the safe area the diodes start to conduct causing the fuse to blow.The Zener Barrier has alternating polarities i. e. interconnected zener diodes are employed and one side is grounded. The Zener Barrier can be used for both alternating voltage signals and direct voltage signals.Depending on the application increased or decreased intrinsic safety parameters apply for serial or parallel connection. For the detailed parameters refer to the Zener Barrier certificate. Application examples can be found in the system description of the Zener Barriers.AC Versionsuitable for Vimpex intrinsically safe products.Key Features1-channelAC versionWorking voltage 26.5 V at 10 ASeries resistance max. 327 Fuse rating 50 mADIN rail mounting

GBP 166.61
1