52 results (0,16917 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Apollo XP95 DIN-Rail Sounder Controller 5 Amperes 55000-182APO

Apollo XP95 DIN-Rail Sounder Controller 5 Amperes 55000-182APO

Please note This product currently has an extended leadtime due to a component shortage. Please contact us for further information.Apollo XP95 DIN-Rail Sounder Controller 5 Amperes 55000-182APOThe DIN-Rail Sounder Controller 5 Amperes is used to control the operation of a zone of externally powered sounders and report their status to the control panel.Electrical DescriptionThe DIN-rail Sounder Controller is loop powered and operates at 1728V DC. It requires a local power supply of 1235V DC to power the external load which may be up to 5A. A polarising diode is required with each alarm device as sounders are operated by voltage reversal provided by a double-pole change-over relay. The sounder circuit is protected by a fuse rated at 5A quick acting.OperationThe Sounder Controller allows sounders to be operated continuously or be pulsed 1 second on 1 second off. Sounders may be operated individually or in groups and whichever address mode has been applied may be synchronised when in pulsed operation. An opto-coupled input is provided to monitor the state of the external power supply. In normal operation the Sounder Controller returns a pre-set analogue value of 16 but in the event of an open or short-circuit fault or of a fault in the external power supply the unit returns a pre-set analogue value of 4.Key FeaturesAllows sounders to be operated continuously or be pulsed 1 second on 1 second offMay be synchronised with loop soundersAn opto-coupled input is provided to monitor the state of the external power supplyFeatures group addressingWill accept a load of up to 5A

GBP 97.03
1

Apollo XP95 DIN-Rail Dual Isolator - 55000-802APO

Apollo XP95 DIN-Rail Dual Isolator - 55000-802APO

Apollo XP95 DIN-Rail Dual Isolator - 55000-802APOThe DIN-Rail Dual Isolator provides two independent isolators which sense and isolate short circuits on Discovery and XP95 loops and spurs.OperationUnder normal operating conditions a low impedance is present between the two negative terminals of each isolator channel so that power and signals are passed to the next base in line. If a short-circuit or abnormally low impedance occurs across the loop the fall in voltage is sensed and the isolator isolates the negative supply in the direction of the fault. In this condition the yellow LED of the affected channel will be illuminated.The isolated section of loop is tested using a current pulse every five seconds. When the short-circuit is removed the power will automatically be restored. The two isolator channels are not interconnected internally and operate completely independently of one another.Key FeaturesLoop-poweredPolarity sensitiveUp to 20 detectors can be installed between isolatorsAllows fully isolated spurs

GBP 55.00
1

Apollo Marine Isolating Base 45681-286MAR

Apollo Marine Isolating Base 45681-286MAR

Apollo Marine Isolating Base 45681-286MARThe Isolating Base senses and isolates short circuit faults on XP95 and Discovery loops and spurs.OperationUnder normal operating conditions a low impedance is present between the IN and OUT terminals of the base so that power and signals pass to the next base in line. If a short-circuit or abnormally low impedance occurs the fall in voltage is sensed and the base isolates the negative supply in the direction of the fault.The isolated section is tested using a current pulse every five seconds. When the short-circuit is removed the power will automatically be restored. If it is a requirement that no device is lost in the event of a single short-circuit fault every detector should be fitted to an isolating base. In applications where it is not necessary to use an isolating base for each detector up to twenty detectors or equivalent surge current may be installed between isolating bases.Key FeaturesUp to 20 detectors or their equivalent load may be installed between isolating basesHigh-brightness LEDDetects wiring short-circuitsMinimises disruption from short-circuits

GBP 16.81
1

Apollo Isolator XP95 and Discovery 55000-720APO

Apollo Isolator XP95 and Discovery 55000-720APO

Apollo Isolator XP95 and Discovery 55000-720APOThe Isolator is placed at intervals on the loop and ensures that in the case of a short circuit only the section between the isolators will be affected. When the short circuit is removed the isolators automatically restore power and data to the isolated section.Key Features Detects wiring short-circuitsMinimises disruption from short-circuitsAutomatic de-isolation on the short-circuit removalUp to 20 detectors or their equivalent load may be installed between isolators

GBP 18.46
1

Apollo Discovery Marine Isolator 55000-721MAR

Apollo Discovery Marine Isolator 55000-721MAR

Apollo Discovery Marine Isolator 55000-721MARThe Discovery Marine Isolator is placed at intervals on the loop and ensures that in the case of a short-circuit only the section between the isolators will be affected. When the short-circuit is removed the isolators automatically restore power and data to the isolated section.Key FeaturesDetects wiring short-circuits using patented technologyMinimises disruption from short-circuitsAutomatic de-isolation on short-circuit removalUp to 20 detectors or equivalent load may be installed between isolators

GBP 30.83
1

Apollo Marine DIN-Rail Dual Isolator 55000-770MAR

Apollo Marine DIN-Rail Dual Isolator 55000-770MAR

Apollo Marine DIN-Rail Dual Isolator 55000-770MARThe Marine DIN-Rail Dual Isolator provides in one housing two independent isolators which sense and isolate short-circuits on loops and spurs. This unit needs to be installed in a suitable enclosure Part No. 29600-239240 or equivalent and secured using the end stops.OperationThe isolators are loop-powered and are polarity sensitive. A maximum of twenty detectors may be installed between isolators. When a short-circuit condition exists on either side of the isolator the yellow LED is illuminated.Under normal operating conditions a low impedance is present between the two negative terminals of each isolator channel so that power and signals are passed to the next base in line.If a short-circuit or abnormally low impedance occurs across the loop the fall in voltage is sensed and the isolator isolates the negative supply in the direction of the fault. In this condition the yellow LED of the affected channel will be illuminated. The isolated section of loop is tested using a current pulse every five seconds. When the short-circuit is removed the power will automatically be restored.Key FeaturesLoop-poweredUp to 20 detectors can be installed between isolatorsAllows fully isolated spurs

GBP 78.92
1

Apollo Conventional Triple IR Flame Detector 55000-019APO

Apollo Conventional Triple IR Flame Detector 55000-019APO

Apollo Conventional Triple IR Flame Detector 55000-019APOThe IR3 Flame Detector is designed for harsh environments in indoor applications. The detector has three sensors which respond to different IR wavelengths to discriminate between flames and spurious sources of radiation.Key Features Selectable output options Conventional two-wire 4-20mA Latching or Non-latching RelayContacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP65 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55C

GBP 1755.00
1

Apollo Conventional Dual IR Flame Detector 55000-060APO

Apollo Conventional Dual IR Flame Detector 55000-060APO

Apollo Conventional Dual IR Flame Detector 55000-060APOThe IR2 Flame Detector is designed for harsh environments in indoor applications. The detector has two sensors which respond to different IR wavelengths to discriminate between flames and spurious sources of radiation.Key Features Selectable output options Conventional two-wire 4-20mA Latching or Non-latching RelayContacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP65 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55C

GBP 1494.48
1

Apollo Conventional UV Dual IR Flame Detector 55000-064APO

Apollo Conventional UV Dual IR Flame Detector 55000-064APO

Apollo Conventional UV Dual IR Flame Detector 55000-064APOThe combination of UV and IR2 detection plus signal processing allows the sensor to be used without risk of false alarms in difficult situations characterised by factors such as flickering blackbody by radiation or arc welding. Key FeaturesSelectable output options Conventional two-wire 4-20mA Latching or Non-latching Relay Contacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP65 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55COperating temperature -10C to 55C

GBP 2152.80
1

Apollo Intelligent Open-Area Clear Beacon - 55000-010APO

Apollo Intelligent Open-Area Clear Beacon - 55000-010APO

Apollo Intelligent Open-Area Clear Beacon - 55000-010APOThe Intelligent Open-Area Visual Indicator has been developed for use in situations where there is a risk that sounders will not be heard.All devices are powered directly from the loop and need no external power supply. They operate at 1728V DC and are polarity sensitive.All the alarm devices can be assigned group addresses as well as individual addresses so that the functional options of the sounder are identical with those of the Sounder Control Unit.Key FeaturesFor use with XP95 Discovery systemsSelf-test fault monitoringIP65 ratedIndividual and group addressingSynchronisation of flashes Comes with Isolating Base as standardLoop-powered

GBP 45.98
1

Apollo Multi-Tone Red Open-Area Sounder Visual Indicator without Isolator 55000-291APO

Apollo Multi-Tone Red Open-Area Sounder Visual Indicator without Isolator 55000-291APO

Apollo Multi-Tone Red Open-Area Sounder Visual Indicator without Isolator 55000-291APOThe Multi-Tone Open-Area Sounder Visual Indicator is designed for use in indoor open areas and can be connected to any Discovery or XP95 system. The sounder visual indicator complements Apollos intelligent and integrated base sounders as well as the Multi-Tone Open-Area Sounder.The Multi-tone Open-Area Alarm Devices are powered directly from the loop and need no external power supply. They operate at 18 28V DC and are polarity sensitive.Key FeaturesChoice of tones on standard device Apollo Slow Whoop and DINTwo volume settings 92dBA and 100dBASynchronisation of alert and evacuate tonesIndividual and group addressingIP21C

GBP 101.80
1

Apollo XP95 Sounder Beacon Base - 45681-331APO

Apollo XP95 Sounder Beacon Base - 45681-331APO

Apollo XP95 Sounder Beacon Base - 45681-331APOThe Sounder Beacon Base are loop powered so needs no external power supply. It operates at 1728V DC and is polarity-sensitive. The Sounder Beacon Base are moulded in polycarbonate and has stainless steel contacts that accept solid or stranded cables of up to 2.5mm.The Sounder Beacon Bases will operate only with control equipment using the Apollo XP95 or Discovery protocol. The features of the Sounder Beacon Base are available only when it is connected to a control panel with the appropriate software.Key FeaturesTwo volume ranges 55-75dBA and 75-91dBAVisual indicator flash rate of once per secondSynchronisation of alert and evacuate tonesSynchronisation of visual indicator flashIndividual and group addressingUnique acoustic and visual indicator self-test

GBP 58.67
1

Apollo XP95 Discovery Isolator Base 45681-211APO

Apollo XP95 Discovery Isolator Base 45681-211APO

Apollo XP95 Isolator Base 45681-211APOThe XP95 Isolator Base is only suitable for use with the Isolator 55000-720. The Isolator Base made of polycarbonate housing with nickel plated stainless steel terminals.The Isolator is placed at intervals on the loop and ensures that in the case of a short circuit only the section between the isolators will be affected. When the short circuit is removed the isolators automatically restore power and data to the isolated section. The Isolator can only be used with an Isolator base and will not fit a standard addressable base.Key FeaturesDetects wiring short-circuits using patented technologyMinimizes disruption from short circuitsAutomatic de-isolation on short-circuit removalUp to 20 detectors or equivalent may be installed between isolators

GBP 2.98
1

Apollo XP95 Integrated Base Sounder with Isolator 45681-277APO

Apollo XP95 Integrated Base Sounder with Isolator 45681-277APO

Apollo XP95 Integrated Base Sounder with Isolator 45681-277APOThe Integrated Base Sounder comprises of a base sounder with integral mounting base and is for use with Discovery or XP95 ranges. It is designed for indoor use. The base sounder is line powered and needs no external power supply. It operates at 1728V DC and is polarity-sensitive.The integrated base sounder is moulded in polycarbonate and has stainless steel contacts that accept solid or stranded cables of up to 2.5mm. The Base Sounder comprises of a base sounder with integral mounting base and is for use with Discovery or XP95 ranges. It is designed for indoor use.Key Features Two tonesTwo volume ranges 55-75dBA and 75-91dBAIndividual and group addressingUnique acoustic self-testBuilt-in isolator

GBP 35.35
1

Apollo RW1700-052APO Reach Output Module

Apollo RW1700-052APO Reach Output Module

Apollo RW1700-052APO Reach Output ModuleThe RW1700-052APO REACH Wireless Output Module is a wireless analogue addressable interface which allows simple integration of third-party equipment with the fire system. The unit is powered entirely from its internal battery supply and is fitted as standard with both a set of change over relay contacts and a 1224V dc output. The output is capable of supplying power for operating low current third party equipment directly from the internal batteries.The REACH range is designed to solve challenging installation scenarios for structures with restricted or complex access and installation conditions such as listed buildings out-buildings temporary structures where wired installation or long site downtime is not possible.Key FeaturesOutput circuits are fully supervised for fault conditionsBi-directional wireless communicationDual channel redundancyFive year product warranty

GBP 213.89
1

Apollo White Weatherproof Multi-Tone Open-Area Sounder Beacon with Isolator - 55000-299APO

Apollo White Weatherproof Multi-Tone Open-Area Sounder Beacon with Isolator - 55000-299APO

Apollo White Weatherproof Multi-Tone Open-Area Sounder Beacon with Isolator - 55000-299APOThe Weatherproof Multi-Tone Open-Area Sounder Visual Indicator is designed for use in outdoor open areas and can be connected to any Discovery or XP95 system. The sounder visual indicator complements Apollos intelligent and integrated base sounders as well as the Multi-Tone Open-Area Sounder.The Multi-tone Open-Area Alarm Devices are powered directly from the loop and need no external power supply. They operate at 18 28V DC and are polarity sensitive. Synchronisation of the tones ensures the integrity of the signal tones from different sounders do not merge into one signal that could be mistaken for a different tone.Key FeaturesChoice of tones on standard device Apollo Slow Whoop and DINIP66 ratedTwo Volume settings 92dBA and 100dBASynchronisation of alert and evacuate tonesIndividual and group addressingBuilt in isolator

GBP 175.15
1

Apollo Exd Conventional Dual IR Flame Detector 55000-061APO

Apollo Exd Conventional Dual IR Flame Detector 55000-061APO

Apollo Exd Conventional Dual IR Flame Detector 55000-061APOThe Flameproof IR2 Flame Detector is designed for use in hazardous environments in indoor applications. The combination of filters and signal processing allows the sensor to be used with a very low risk of false alarms in difficult situations characterised by factors such as flickering lights. Baseefa has certified the detector for compliance to standards EN 60079-0 EN 60079-1 and EN 61241-1 Key Features ATEX IECEx certified II2GD Ex d IIC T4 Gb EE tb IIICT135 C Db IP66 A21 Zones 1 21 2 and 22Selectable output options Conventional two-wire 4-20mA Latching or Non-latching Relay Contacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP66 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55C

GBP 2129.40
1

Apollo Exd Conventional Triple IR Flame Detector 55000-062APO

Apollo Exd Conventional Triple IR Flame Detector 55000-062APO

Apollo Exd Conventional Triple IR Flame Detector 55000-062APOThe Flameproof IR3 Flame Detector is designed for use in hazardous environments in indoor and outdoor applications.It is sensitive to low-frequency flickering infra-red radiation emitted by flames during combustion. The sensor operates even through a layer of oil dust water vapour or ice. Baseefa has certified the detector for compliance to standards EN 60079-0 EN 60079-1 and EN 61241-1 Key Features ATEX IECEx certified II2GD Ex d IIC T4 Gb Ex tb IIICT135 C Db IP66 A21 Zones 1 21 2 and 22Selectable output options Conventional two-wire 4-20mA Latching or Non-latching Relay Contacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP66 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55C

GBP 2340.00
1

Apollo I.S. Conventional Triple IR Flame Detector 55000-063APO

Apollo I.S. Conventional Triple IR Flame Detector 55000-063APO

Apollo I.S. Conventional Triple IR Flame Detector 55000-063APOThe IS IR3 Flame Detector is designed for harsh environments in either indoor or outdoor applications. It is sensitive to low frequency flickering IR radiation emitted from flames during combustion.The sensor operates even through a layer of oil dust water vapour or ice. These detectors have been approved byBaseefa to standards EN50014 EN50020 and EN50284. The requirements of Directive 949EC the Atmosphere Explosives ATEX directive have also been met.Key Features ATEX IECEx certified II 1 GCENELECIEC Certified Ga Ex ia IIC T4Selectable output options Conventional two-wire 4-20mA Latching or Non-latching RelayContacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP65 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 40C T4Operating temperature -10C to 55C

GBP 2233.04
1

Apollo White Multi-Tone Open-Area Sounder Beacon with Isolator - 55000-294APO

Apollo White Multi-Tone Open-Area Sounder Beacon with Isolator - 55000-294APO

Apollo White Multi-Tone Open-Area Sounder Beacon with Isolator - 55000-294APOThe Multi-Tone Open-Area Sounder Visual Indicator is designed for use in indoor open areas and can be connected to any Discovery or XP95 system. The sounder visual indicator complements Apollos intelligent and integrated base sounders as well as the Multi-Tone Open-Area Sounder.The Multi-tone Open-Area Alarm Devices are powered directly from the loop and need no external power supply. They operate at 18 28V DC and are polarity sensitive. Synchronisation of the tones ensures the integrity of the signal tones from different sounders do not merge into one signal that could be mistaken for a different tone.Key FeaturesChoice of tones on standard device Apollo Slow Whoop and DINTwo volume settings 92dBA and 100dBASynchronisation of alert and evacuate tonesIndividual and group addressingBuilt in isolatorIP21C

GBP 102.28
1

Apollo Exd Conventional UV Dual IR Flame Detector 55000-065APO

Apollo Exd Conventional UV Dual IR Flame Detector 55000-065APO

Apollo Exd Conventional UV Dual IR Flame Detector 55000-065APOThe Flameproof UVIR2 Flame Detector is designed for hazardous environments in either indoor or outdoor applications where open fires may be expected. False alarms from flickering sunlight arc welding or lightning are avoided by the combination of UV and dual IR signal processing techniques.It detects almost all flames including those invisible to the naked eye e.g. hydrogen fires. Certified by ISSOP for compliance with standards EN50014 EN50018 and EN50281. Key Features ATEX Certified II 2 G DCENELECIEC Certified EEx d - IIC T6- Zones 1 21 2 and 22Class 1 sensitivity to EN54-10 detects 0.1m2 fires at 25mHighest optical interference immunitySelectable output options Conventional two-wire 4-20mA Relay Contacts - FireFault Pre alarm Latching or Non-latchingSelectable response speedRemote control self-testLow power consumptionIP66 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55C

GBP 2340.00
1

Apollo Series 65 End-of-Line Relay Base 12V - 45681-247APO

Apollo Series 65 End-of-Line Relay Base 12V - 45681-247APO

Apollo Series 65 End-of-Line Relay Base 12V - 45681-247OperationSeries 65 Relay Bases are primarily intended for use with control units using 4-wire detector supply and alarm initiating circuits. Where local codes allow they may also be used in 2 and 4-wire circuits to provide volt-free control signals to an auxiliary system such as an automatic door closer. They are not suitable for use in systems where it is specified or required that operation of the auxiliary system shall be fail-safe and must not be used with any other type of detector.Options45681-247 for circuits having a supply voltage between 9- and 18-volts DC and 45681-248 for circuits having a supply voltage between 16- and 33-volts DC.Product InformationThe Series 65 End-of-Line EOL Relay Base is intended for use with four-wire circuits and features two sets of changeover contacts and a power supervision relay.Key FeaturesDetector locking mechanismOne way fitEasy to wireContains an earth connector

GBP 22.14
1

Apollo Series 65 End-of-Line Relay Base - 24V 45681-248APO

Apollo Series 65 End-of-Line Relay Base - 24V 45681-248APO

Apollo Series 65 End-of-Line Relay Base 24V - 45681-248OperationSeries 65 Relay Bases are primarily intended for use with control units using 4-wire detector supply and alarm initiating circuits. Where local codes allow they may also be used in 2 and 4-wire circuits to provide volt-free control signals to an auxiliary system such as an automatic door closer. They are not suitable for use in systems where it is specified or required that operation of the auxiliary system shall be fail-safe and must not be used with any other type of detector.Options45681-247 for circuits having a supply voltage between 9- and 18-volts DC and 45681-248 for circuits having a supply voltage between 16 and 33 volts DC.Product InformationThe Series 65 End-of-Line EOL Relay Base is intended for use with four-wire circuits and features two sets of changeover contacts and a power supervision relay.Key FeaturesDetector locking mechanismOne way fitEasy to wireContains an earth connector

GBP 22.14
1

Apollo White Multi-Tone Open-Area Sounder - 55000-279APO

Apollo White Multi-Tone Open-Area Sounder - 55000-279APO

Apollo White Multi-Tone Open-Area Sounder - 55000-279APOThe Multi-Tone Open-Area Sounder is designed for use in open areas and can be connected to any Discovery or XP95 system. The Multi-tone Open-Area Alarm Devices are powered directly from the loop and need no external power supply. They operate at 18 28V DC and are polarity sensitive.Synchronisation of the tones ensures the integrity of the signal tones from different sounders do not merge into one signal that could be mistaken for a different tone. A nominal sound output of 100dBA is achieved at a current consumption of 5mA in the case of the sounder and 9mA for the sounder beacon.Many control panels will be able to drive up to 20 sounders per loop on average. The maximum number of sounders that may be connected to a particular loop should however be determined by a loop loading calculation using the Apollo Loop Calculator.Key FeaturesUpdated to include choice of tones Apollo slow whoop and DINTwo volume settings 92dBA and 100dBASynchronisation of tonesIndividual and group addressingLoop PoweredRed or White optionsIP21C rated

GBP 73.40
1

Apollo XPander Combined Sounder Base XPA-WB-14036-APO

Apollo XPander Combined Sounder Base XPA-WB-14036-APO

Apollo XPander Combined Sounder BaseXPA-WB-14036-APOThe XPander Combined Sounder and Detector is wireless and designed to provide one-point detection and notification.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessAvailable with a choice of XPander detectorsBi-directional monitored radio platformA choice of four tone pairsCertified to EN 54-25

GBP 318.79
1